1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
|
#ifndef config_bistro_H
#define config_bistro_H
/*
* Firmware configuration header.
*
* Bistro default configuration file. 2017, (C) Flintrock (FR).
* Generally kept setup for a TA v1 driver, but exact options may fluctuate.
* This config is meant to be maintained with all latest options in the comments.
* Other configs will only get new options added if relevant to that config.
*
* To work with tk-bistro and other compatible software.
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/*
* =========================================================================
* Settings to modify per driver
*/
/////////////// Choose a layout////////////////
//#define FET_7135_LAYOUT //FET+1
#define TRIPLEDOWN_LAYOUT //TA tripple
//#define NANJG105D_LAYOUT // biscotti/convoy/nanjg105D
//#define BLFA6_LAYOUT // BLFA6, FET+1, OTC and star3
//#define NANJG_LAYOUT // specify an I/O pin layout
//#define QUADRUPLEDOWN_LAYOUT // Yes, that right :)
//#define CUSTOM_LAYOUT // go define it for however you want to wire your driver.
//**** You can now easily customize layouts in fr-tk-attiny.h :
// choose the file that defines your modegruops (so we can easily keep more)
#define MODEGROUPS_H "modegroups/modegroups-TA-tripple.h"
//#define MODEGROUPS_H "modegroups/modegroups-biscotti.h"
//#define MODEGROUPS_H "modegroups/modegroups-BLFA6.h"
//#define MODEGROUPS_H "modegroups/modegroups-classic.h"
//#define MODEGROUPS_H "modegroups/modegroups-trippledown.h"
/************************* Misc utility configs*************************************/
//#define VOLTAGE_CAL // builds a driver that just blinks ADC reading, set the VOLTAGE mode below.
//#define STRIPPED // use for debugging, strips many features to make more space for debug compiler options or testing functions.
// customize it below
//#define OTSM_debug //may require STRIPPED to fit. //Will blink out number of wakes (see SLEEP_TIME_EXPONENT) on short clicks, before entering mode.
/************************************OFF-TIME CONFIGS**********************************/
//USE redundancy to make noinit off memory safer (if used at all) redundancy 4 requires 38 bytes.
// This is only used if OTC and OTSM are not used and you have a clicking switch.
//#define USE_SAFE_PRESSES // enable redundancy 4 requires 38 bytes.
// redundancy level. Default is 4, but 3 could save some space, 2 has lower than 1 in 255 chance of failure:
// 3 has maybe 1 in 2,800 odds (based observations that 1's twice as probable as 0's)
// 4 should have 1 in 69,000 odds of failure.
// Failure rate is most likely per chip, not per click, but could be a little of both.
//#define N_SAFE_BYTES 4
#define OFFTIM3 // Use short/med/long off-time presses instead of just short/long
#define USE_OTC // use off time cap.
// Off-time sleep mode by -FR, thanks to flashy Mike and Mike C for early feasibility test with similar methods.
//#define USE_OTSM // USE OTSM. Pin must be defined in the layout too.
//#define OTSM_USES_OTC // use OTC cap for extra power on OTSM (sets it output high to charge up)
#define OTSM_powersave // Also works without OTSM to reduce moon-mode drain.
// Squeeze out a bit more off-time by saving power during
// shutoff detection (so at all times). Implements ms resolution (could be less) idle sleeps in place of delay.
// Seems to add at 0.5s of sleep at 3.1V 30uF cap, starting with only 0.75 that matters.
// But at higher voltages, it's still only 0.5s additional, not multiplicative.
// Also adds about 12 bytes that could be used for about two more mode groups instead :P
// Traditionally Cap values defined in tk-calibration
// But wake times in OTSM are not a calibration, just a configuration, so they go here.
// Times are in decimal seconds. short (med) wakes are <, not = to wake_time_short(med)
#define SLEEP_TIME_EXPONENT 4 // OTSM clicky sleep will be increments of 16ms*2^STE
// so 0 is 16, 1 is 32, 2 is 64, 3 is 128, 4 is 0.25s, 5 is 0.5s etc.
// To allow long click times use 4. For 1/8s resolution, use 3.
#define wake_time_short 0.5 // 0.5s : Short press is up to 0.5 s
#define wake_time_med 1.25 // this is limited by cap performance, but setting it high won't hurt
// Since anything beyond the cap capacity will be read as long anyway.
// It's also the long-press off-threshold for e-switch operation.
/*****************************END OTSM CONGIGS*********************************/
//#define USE_ESWITCH // pin must be defined in the layout too.
//#define USE_ESWITCH_LOCKOUT_TOGGLE // enables menu to turn off eswitch, experimental, maybe be removed.
/**********************VOLTAGE CONFIG****************************************/
#define VOLTAGE_MON // Comment out to disable LVP
//You should leave one (but only one) of the next two uncommented.
#define READ_VOLTAGE_FROM_VCC // inverted "internal" Vcc voltage monitoring
// Works well for 1S lights without worrying about resistor values.
//#define READ_VOLTAGE_FROM_DIVIDER // classic voltage reading
//#define REFERENCE_DIVIDER_READS_TO_VCC // default is 1.1V, but this is needed for divider reading with OTSM on the voltage pin.
// This should normally be used with an LDO. For 1S (non-LDO or 5.0VLDO) just avoid the problem with READ_VOLTAGE_FROM_VCC.
/*** Enable battery indicator mode? */
#define USE_BATTCHECK
// Choose a battery indicator style
//#define BATTCHECK_4bars // up to 4 blinks
//#define BATTCHECK_8bars // up to 8 blinks
#define BATTCHECK_VpT // Volts + tenths
/******theremal protection: ***/
#define TEMPERATURE_MON // You can set starting temperature in the "maxtemp" setting in config options first boot options.
#define USE_TEMP_CAL
// For attiny 13, there is no temp monitor, but you can use turbo timeout as a safety instead.
// better yet.. use the whole condition below to customize build based on chip:
//#if ATTINY==13 // thermal control depending on chip.
//#define USE_TURBO_TIMEOUT
//#define TURBO_TIMEOUT 45 // timeout in seconds.
//#else
//#define TEMPERATURE_MON
//#define USE_TEMP_CAL
//#endif
/*******Mode features***********/
#define USE_MUGGLE_MODE // compile in use of muggle mode
#define USE_REVERSE_MODES // compile in use of reverse modes
#define USE_MOON // compile in moon mode control
/*********Misc************/
//#define INLINE_STROBE inline // inline the strobe function, saves a surprisingly
// large amount of space if only one simple strobe is used.
// some special strobes don't count in that, so worth jus trying.
// Options for first bootup/default:
#define USE_FIRSTBOOT // FR notes this only costs a little since not using it implements alternative checks anyway.
#define INIT_MODEGROUP 0 // which mode group will be default, mode groups below start at zero, select the mode group you want and subtract one from the number to get it by defualt here
#define INIT_ENABLE_MOON 1 // Should we add moon to the set of modes?
#define INIT_REVERSE_MODES 0 // flip the mode order?
#define INIT_MEMORY 0 // mode memory, or not
#define INIT_OFFTIM3 7 // enable medium-press by default?
#define INIT_MUGGLE_MODE 0 // simple mode designed for mugglesotsm
#define INIT_LOCKSWITCH 0 // 0 => E-swtich enabled, 1 => locked.
#define INIT_MAXTEMP 88 // maximum temperature
#define BLINK_SPEED 750
// This is used to simplify the toggle function
// eliminating mode_override, using this threshold instead:
#define MINIMUM_OVERRIDE_MODE 245 // DO NOT EDIT. DO NOT DEFINE ANY STROBES HIGER OR EQUAL TO THIS.
/******* Select Which Strobes to compile in**** *********************/
////Must still be connected to a mode group or hidden mode to be used, enabled but unused modes don't get optimized out
#define BATTCHECK 244 // Convenience code for battery check mode
//mode codes for strobes, must be less than MINIMUM_OVERRIDE_MODE
#define BIKING_STROBE 243 // Single flash biking strobe mode
//#define FULL_BIKING_STROBE // Stutter bike strobe, uncomment to enable
//#define POLICE_STROBE 242 // Dual mode alternating strobe
//#define RANDOM_STROBE 241
//#define SOS 240
//#define STROBE_8HZ 239
#define STROBE_10HZ 238
#define STROBE_16HZ 237
#define STROBE_OLD_MOVIE 236
#define STROBE_CREEPY 235 // Creepy strobe mode, or really cool if you have a bunch of friends around
//#define RAMP 234 //Ramping "strobe"
#ifdef STRIPPED // define what you want to remove in stripped mode
#undef TEMPERATURE_MON
#undef VOLTAGE_MON
#define NO_STROBES // don't use strobes (not automatically stripped from modes though, result can be undefined)
#undef USE_BATTCHECK
#endif
/**********************************************************************************
**********************END OF CONFIGURATION*****************************************
***********************************************************************************/
#endif
|