1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
#ifndef HWDEF_NOCTIGON_K1_12V_H
#define HWDEF_NOCTIGON_K1_12V_H
/* Noctigon K1 driver layout (attiny1634)
* (originally known as Emisar D1S V2)
*
* Pin / Name / Function
* 1 PA6 (none) (PWM1B) (reserved for DD drivers)
* 2 PA5 R: red aux LED (PWM0B)
* 3 PA4 G: green aux LED
* 4 PA3 B: blue aux LED
* 5 PA2 (none) (reserved for L: button LED (on some models))
* 6 PA1 (none)
* 7 PA0 (none)
* 8 GND GND
* 9 VCC VCC
* 10 PC5 (none)
* 11 PC4 (none)
* 12 PC3 RESET
* 13 PC2 (none)
* 14 PC1 SCK
* 15 PC0 boost PMIC enable (PWM0A not used)
* 16 PB3 main LED PWM (PWM1A)
* 17 PB2 MISO
* 18 PB1 MOSI / battery voltage (ADC6)
* 19 PB0 Opamp power
* 20 PA7 e-switch (PCINT7)
* ADC12 thermal sensor
*
* Main LED power uses one pin to turn the Opamp on/off,
* and one pin to control Opamp power level.
* All brightness control uses the power level pin, with 4 kHz 10-bit PWM.
* The on/off pin is only used to turn the main LED on and off,
* not to change brightness.
*/
#ifdef ATTINY
#undef ATTINY
#endif
#define ATTINY 1634
#include <avr/io.h>
#define PWM_CHANNELS 1
#define PWM_BITS 10 // 0 to 1023 at 4 kHz, not 0 to 255 at 16 kHz
#define PWM_TOP 1023
#define SWITCH_PIN PA7 // pin 20
#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt
#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0]
#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
#define SWITCH_PORT PINA // PINA or PINB or PINC
#define PWM1_PIN PB3 // pin 16, Opamp reference
#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3
#define LED_ENABLE_PIN PB0 // pin 19, Opamp power
#define LED_ENABLE_PORT PORTB // control port for PB0
#define LED2_ENABLE_PIN PC0 // pin 15, boost PMIC enable
#define LED2_ENABLE_PORT PORTC // control port for PC0
#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened
#define VOLTAGE_PIN PB1 // Pin 18 / PB1 / ADC6
// pin to ADC mappings are in DS table 19-4
#define VOLTAGE_ADC ADC6D // digital input disable pin for PB1
// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6
#define VOLTAGE_ADC_DIDR DIDR1 // DIDR channel for ADC6D
// DS tables 19-3, 19-4
// Bit 7 6 5 4 3 2 1 0
// REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0
// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1
// divided by ...
// REFS[1:0] = 1, 0 for internal 1.1V reference
// other bits reserved
#define ADMUX_VOLTAGE_DIVIDER 0b10000110
#define ADC_PRSCL 0x07 // clk/128
// Raw ADC readings at 4.4V and 2.2V
// calibrate the voltage readout here
// estimated / calculated values are:
// (voltage - D1) * (R2/(R2+R1) * 256 / 1.1)
// D1, R1, R2 = 0, 330, 100
#ifndef ADC_44
//#define ADC_44 981 // raw value at 4.40V
#define ADC_44 967 // manually tweaked so 4.16V will blink out 4.2
#endif
#ifndef ADC_22
//#define ADC_22 489 // raw value at 2.20V
#define ADC_22 482 // manually tweaked so 4.16V will blink out 4.2
#endif
// this light has aux LEDs under the optic
#define AUXLED_R_PIN PA5 // pin 2
#define AUXLED_G_PIN PA4 // pin 3
#define AUXLED_B_PIN PA3 // pin 4
#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC
#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC
#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC
// with so many pins, doing this all with #ifdefs gets awkward...
// ... so just hardcode it in each hwdef file instead
inline void hwdef_setup() {
// enable output ports
// boost PMIC on/off
DDRC = (1 << LED2_ENABLE_PIN);
// Opamp level and Opamp on/off
DDRB = (1 << PWM1_PIN)
| (1 << LED_ENABLE_PIN);
// aux R/G/B
DDRA = (1 << AUXLED_R_PIN)
| (1 << AUXLED_G_PIN)
| (1 << AUXLED_B_PIN)
;
// configure PWM
// Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
// pre-scale for timer: N = 1
// WGM1[3:0]: 0,0,1,1: PWM, Phase Correct, 10-bit (DS table 12-5)
// CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6)
// COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4)
// COM1B[1:0]: 0,0: PWM OC1B disabled (DS table 12-4)
TCCR1A = (1<<WGM11) | (1<<WGM10) // 10-bit (TOP=0x03FF) (DS table 12-5)
| (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4)
| (0<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4)
;
TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6)
| (0<<WGM13) | (0<<WGM12) // phase-correct PWM (DS table 12-5)
;
// set up e-switch
PUEA = (1 << SWITCH_PIN); // pull-up for e-switch
SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt
}
#define LAYOUT_DEFINED
#endif
|