~sammyshp/flashlight-firmware/ramp-border-delay-anduril2 : changes

~sammyshp/flashlight-firmware/ramp-border-delay-anduril2 » Changes from revision 619

From Revision 618 to 599

Rev	Summary	Authors	Date
618	made it possible to use autolock in simple UI made it possible to use autolock in simple UI (requires the user to set it up, so it won't happen to new users unless they do it on purpose)	Selene Scriven	2 years ago
617	added documentation for the global config menu and jump star... added documentation for the global config menu and jump start level	Selene Scriven	2 years ago
616	moved jump start into FSM so it'll be more universal and the... moved jump start into FSM so it'll be more universal and the app won't need special clauses (also adjusted KR4 jump start levels a bit)	Selene Scriven	2 years ago
615	made jump start level configurable at runtime, and made it a... made jump start level configurable at runtime, and made it activate in more places	Selene Scriven	2 years ago
614	force reset PWM phase when turning on from zero force reset PWM phase when turning on from zero (to make initial response consistent) (otherwise, it can randomly take up to ~16ms to turn on)	Selene Scriven	2 years ago
613	added Emisar DT8 in PRODUCTS added Emisar DT8 in PRODUCTS	Selene Scriven	2 years ago
612	merged digitalcircuit's branch to make autolock timer config... merged digitalcircuit's branch to make autolock timer configurable at build time	Selene Scriven	2 years ago
611	merged digitalcircuit's anduril2_opt_disable_autocal_therm b... merged digitalcircuit's anduril2_opt_disable_autocal_therm branch, allowing configs to disable the thermal autocalibration feature	Selene Scriven	2 years ago
610	fixed spurious warnings in level_calc on multi-channel light... fixed spurious warnings in level_calc on multi-channel lights (also fixed reported values being too low by a factor of channel.pwm_min)	Selene Scriven	2 years ago
609	made dynamic PWM phase-correct; replaced brute-force phase r... made dynamic PWM phase-correct; replaced brute-force phase reset to avoid flickering (I didn't see any flickering on my lights, but SammysHP reported it was visible)	Selene Scriven	2 years ago
608	set KR4 default floor higher at Hank's request, set KR4 default floor higher at Hank's request, and reduced the jump-start-moon power a bit too (he says both are good now, but I don't have hardware to measure it myself) The higher floor is because, when the driver is really hot from being on turbo, going directly to moon causes the LEDs to turn off for a while until the driver cools. The new floor is the lowest level where post-turbo activation works reliably. However, it should turn on even at the level 1/150 when it's not hot.	Selene Scriven	2 years ago
607	clarified the new level_calc calculations a bit, experimente... clarified the new level_calc calculations a bit, experimented to make sure things are right	Selene Scriven	2 years ago
606	calibrated KR4 jump-start-moon, may be too high on some olde... calibrated KR4 jump-start-moon, may be too high on some older hardware	Selene Scriven	2 years ago
605	KR4 thermal regulation no longer needs overrides, because dy... KR4 thermal regulation no longer needs overrides, because dynamic PWM makes the defaults work better (the overrides were mostly needed as a side effect of having 1024 PWM steps instead of 256)	Selene Scriven	2 years ago
604	got PFM / dynamic PWM actually working on Noctigon KR4 got PFM / dynamic PWM actually working on Noctigon KR4 (and also added "jump start moon" to it) (and generally finished adding dynamic PWM support to FSM)	Selene Scriven	2 years ago
603	changed Noctigon KR4 from fixed to dynamic PWM TOP value, fo... changed Noctigon KR4 from fixed to dynamic PWM TOP value, for later use	Selene Scriven	2 years ago
602	made PWM TOP value configurable at command line in level_cal... made PWM TOP value configurable at command line in level_calc.py, and added a "dynamic PWM" feature (uses a different PWM TOP at each of the first N ramp levels, to increase resolution at bottom end of ramp)	Selene Scriven	2 years ago
601	added a "jump start moon" option for hold-from-off, for ligh... added a "jump start moon" option for hold-from-off, for lights with slow-activating circuits (briefly pulses the light at a higher level to wake up the circuit faster)	Selene Scriven	2 years ago
600	made blink_once() brightness configurable per build made blink_once() brightness configurable per build	Selene Scriven	2 years ago
599	document the actual maximum for manual memory timer (~140 mi... document the actual maximum for manual memory timer (~140 minutes, not 255)	Selene Scriven	2 years ago

Older »