1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
|
// Mateminco MT18S / Astrolux MF01S driver layout
// Copyright (C) 2019-2023 Selene ToyKeeper
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
/*
* ----
* Reset -|1 8|- VCC (unused)
* eswitch -|2 7|- Voltage divider (2S)
* AUX LED -|3 6|- PWM (FET)
* GND -|4 5|- PWM (smaller FET)
* ----
*/
#define ATTINY 85
#include <avr/io.h>
#define HWDEF_C_FILE hwdef-emisar-d4.c
// channel modes
// * 0. small FET + big FET stacked
#define NUM_CHANNEL_MODES 1
enum CHANNEL_MODES {
CM_MAIN = 0,
};
#define DEFAULT_CHANNEL_MODE CM_MAIN
// right-most bit first, modes are in fedcba9876543210 order
#define CHANNEL_MODES_ENABLED 0b00000001
#define PWM_CHANNELS 2 // old, remove this
#define PWM_BITS 8 // attiny85 only supports up to 8 bits
#define PWM_GET PWM_GET8
#define PWM_DATATYPE uint8_t
#define PWM_DATATYPE2 uint16_t
#define PWM1_DATATYPE uint8_t // little FET ramp
#define PWM2_DATATYPE uint8_t // big FET ramp
#define PWM_TOP_INIT 255 // highest value used in top half of ramp
// little FET channel
#define CH1_PIN PB0 // pin 5, 1x7135 PWM
#define CH1_PWM OCR0A // OCR0A is the output compare register for PB0
// big FET channel
#define CH2_PIN PB1 // pin 6, FET PWM
#define CH2_PWM OCR0B // OCR0B is the output compare register for PB1
// lighted button and 1-channel front aux
#define AUXLED_PIN PB4 // pin 3
// e-switch
#ifndef SWITCH_PIN
#define SWITCH_PIN PB3 // pin 2
#define SWITCH_PCINT PCINT3 // pin 2 pin change interrupt
#endif
#define USE_VOLTAGE_DIVIDER // use a voltage divider on pin 7, not VCC
#ifndef VOLTAGE_PIN
#define VOLTAGE_PIN PB2 // pin 7, voltage ADC
#define VOLTAGE_CHANNEL 0x01 // MUX 01 corresponds with PB2
#define VOLTAGE_ADC ADC1D // Digital input disable bit corresponding with PB2
// inherited from tk-attiny.h
//#define VOLTAGE_ADC_DIDR DIDR0 // DIDR for ADC1
// 1.1V reference, left-adjust, ADC1/PB2
//#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | (1 << ADLAR) | VOLTAGE_CHANNEL)
// 1.1V reference, no left-adjust, ADC1/PB2
#define ADMUX_VOLTAGE_DIVIDER ((1 << V_REF) | VOLTAGE_CHANNEL)
#endif
#define ADC_PRSCL 0x07 // clk/128
// Raw ADC readings at 4.4V and 2.2V (in-between, we assume values form a straight line)
#ifndef ADC_44
#define ADC_44 (234*4)
#endif
#ifndef ADC_22
#define ADC_22 (117*4)
#endif
#define FAST 0xA3 // fast PWM both channels
#define PHASE 0xA1 // phase-correct PWM both channels
inline void hwdef_setup() {
// configure PWM channels
DDRB = (1 << CH1_PIN)
| (1 << CH2_PIN);
TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...)
TCCR0A = PHASE;
// configure e-switch
PORTB = (1 << SWITCH_PIN); // e-switch is the only input
PCMSK = (1 << SWITCH_PIN); // pin change interrupt uses this pin
}
#define LAYOUT_DEFINED
|