1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
|
// Wurkkos TS10 driver layout
// Copyright (C) 2021-2023 gchart, Selene ToyKeeper
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
/*
* (based on BLF Q8-t1616 driver layout)
* Driver pinout:
* eSwitch: PA5
* Aux LED: PB5
* PWM FET: PB0 (TCA0 WO0)
* PWM 1x7135: PB1 (TCA0 WO1)
* Voltage: VCC
*/
#define ATTINY 1616
#include <avr/io.h>
#define HWDEF_C_FILE hwdef-wurkkos-ts10.c
// allow using aux LEDs as extra channel modes
#include "chan-aux.h"
// channel modes:
// * 0. FET+7135 stacked
// * 1. aux LEDs
#define NUM_CHANNEL_MODES 2
enum CHANNEL_MODES {
CM_MAIN = 0,
CM_AUX
};
#define DEFAULT_CHANNEL_MODE CM_MAIN
// right-most bit first, modes are in fedcba9876543210 order
#define CHANNEL_MODES_ENABLED 0b00000001
#define PWM_CHANNELS 2 // old, remove this
#define PWM_BITS 16 // dynamic 16-bit, but never goes over 255
#define PWM_GET PWM_GET8
#define PWM_DATATYPE uint16_t // is used for PWM_TOPS (which goes way over 255)
#define PWM_DATATYPE2 uint16_t // only needs 32-bit if ramp values go over 255
#define PWM1_DATATYPE uint8_t // 1x7135 ramp
#define PWM2_DATATYPE uint8_t // DD FET ramp
// PWM parameters of both channels are tied together because they share a counter
#define PWM_TOP TCA0.SINGLE.PERBUF // holds the TOP value for for variable-resolution PWM
#define PWM_TOP_INIT 255 // highest value used in top half of ramp
// not necessary when double-buffered "BUF" registers are used
#define PWM_CNT TCA0.SINGLE.CNT // for resetting phase after each TOP adjustment
// 1x7135 channel
#define CH1_PIN PB1
#define CH1_PWM TCA0.SINGLE.CMP1BUF // CMP1 is the output compare register for PB1
// DD FET channel
#define CH2_PIN PB0
#define CH2_PWM TCA0.SINGLE.CMP0BUF // CMP0 is the output compare register for PB0
// e-switch
#define SWITCH_PIN PIN5_bp
//#define SWITCH_PCINT PCINT0
#define SWITCH_PORT VPORTA.IN
#define SWITCH_ISC_REG PORTA.PIN2CTRL
#define SWITCH_VECT PORTA_PORT_vect
#define SWITCH_INTFLG VPORTA.INTFLAGS
//#define PCINT_vect PCINT0_vect
// average drop across diode on this hardware
#ifndef VOLTAGE_FUDGE_FACTOR
#define VOLTAGE_FUDGE_FACTOR 7 // add 0.35V
#endif
// front-facing aux LEDs
#define AUXLED_PIN PIN5_bp
#define AUXLED_PORT PORTB
inline void hwdef_setup() {
// set up the system clock to run at 10 MHz instead of the default 3.33 MHz
_PROTECTED_WRITE( CLKCTRL.MCLKCTRLB,
CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
//VPORTA.DIR = ...;
// Outputs
VPORTB.DIR = PIN0_bm // DD FET
| PIN1_bm // 7135
| PIN5_bm; // Aux LED
//VPORTC.DIR = ...;
// enable pullups on the unused pins to reduce power
PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc; // eSwitch
PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // FET channel
//PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // 7135 channel
PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
// set up the PWM
// https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
// PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
// PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
// PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
// For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
// For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
// See the manual for other pins, clocks, configs, portmux, etc
TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm
| TCA_SINGLE_CMP1EN_bm
| TCA_SINGLE_WGMODE_DSBOTTOM_gc;
TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc
| TCA_SINGLE_ENABLE_bm;
PWM_TOP = PWM_TOP_INIT;
}
#define LAYOUT_DEFINED
|