~toykeeper/flashlight-firmware/multi-channel : changes

~toykeeper/flashlight-firmware/multi-channel » Changes from revision 816

From Revision 689 to 670

Rev	Summary	Authors	Date
689	lockout mode: fixed manual memory timer and tint, added 3H n... lockout mode: fixed manual memory timer and tint, added 3H next channel, and made 3H+ use mem level instead of lowest moon (this is needed for making the channel discernible, and also helps make aux LED controls stand out more) The 3H mapping allows users to change channels without leaving lockout, which was possible before with 3H to ramp tint, but doesn't work in new multi-channel code because it uses 3C instead... and 3C is already used. So the new 3H does sort of what the old 3H did, but in a way which is more relevant to the new channel system.	Selene ToyKeeper	1 year ago
688	D4v2: tweaked ramp to make it smoother D4v2: tweaked ramp to make it smoother	Selene ToyKeeper	1 year ago
687	D4v2 FET+1 model: works again, and now uses dynamic PWM (low... D4v2 FET+1 model: works again, and now uses dynamic PWM (lower lows) (also added generic channel modes for RGB aux LEDs)	Selene ToyKeeper	1 year ago
686	RGB aux: always preview in high mode, and show voltage durin... RGB aux: always preview in high mode, and show voltage during 3-second post-off period	Selene ToyKeeper	1 year ago
685	changed lockout RGB aux default to blinking voltage, instead... changed lockout RGB aux default to blinking voltage, instead of blinking disco	Selene ToyKeeper	1 year ago
684	only use 2-color strobe in tactical mode if it's on main LED... only use 2-color strobe in tactical mode if it's on main LEDs, not aux	Selene ToyKeeper	1 year ago
683	tactical mode: use police strobe by default, if it exists tactical mode: use police strobe by default, if it exists	Selene ToyKeeper	1 year ago
682	Noctigon KR4-tintramp updated to use new channel system Noctigon KR4-tintramp updated to use new channel system (was easy since it just uses the generic Emisar-2ch build with a couple small overrides)	Selene ToyKeeper	1 year ago
681	whitespace cleanup whitespace cleanup	Selene ToyKeeper	1 year ago
680	change channel mode per config step in channel mode menu change channel mode per config step in channel mode menu (to show which channel mode is being edited) also, avoid setting channel mode again if it's not going to change (this prevents unnecessary flickering)	Selene ToyKeeper	1 year ago
679	made sleep voltage work on attiny1616 again made sleep voltage work on attiny1616 again (oops, it has no "ADC Noise Reduction" mode... needs different setup code)	Selene ToyKeeper	1 year ago
678	put RGB aux LEDs in high mode for 3 seconds after light goes... put RGB aux LEDs in high mode for 3 seconds after light goes to sleep (much easier to see the voltage this way, including post-turbo sag)	Selene ToyKeeper	1 year ago
677	fixed bug behind K93_LOCKOUT_KLUDGE which could exit lockout... fixed bug behind K93_LOCKOUT_KLUDGE which could exit lockout in solid aux mode (also reduced avg standby power by about 15 uA) (also fixed oscillating voltage mode colors, I think) The bug happened because sometimes sleep LVP would get triggered, because the ADC would read zero under some conditions. This in turn happened because the ADC needs the MCU to be at least partially awake in order to finish a measurement. So in standby mode, with the MCU only waking up very briefly to send a sleep tick and go back to sleep, the ADC required several cycles (like 375ms to 625ms) to finish a single measurement. This varied depending on how many instructions the MCU executed while it was awake. In the single-color mode, so few instructions were being executed that the ADC seemed to time out and abort its measurement, returning a zero. Then a low voltage warning was sent, which knocked the light back into "Off" mode. Adding no-op instructions inside the single-color clause was sufficient to prevent the ADC from timing out, because it kept the MCU awake just barely long enough. But it was a kludge, and it still took like half a second to finish a measurement, and the measurements were noisy. It also used more power, because it required keeping the ADC powered on far too long. This fix puts the MCU into "ADC Noise Reduction" mode instead, when a voltage measurement is needed during sleep. It reduces noise to make measurements more stable... but more importantly, it lets the measurement finish in like 0.5ms instead of 500ms. So it uses less power and isn't dependent on the number of calculations the MCU does during each "sleep tick". As a bonus, this can also measure voltage much more often, while still using less total energy than before. It was once every 8 seconds, and now it's once per second. Avg power use in aux low mode, on a D4Sv2: (avg of 30k samples each) - before: 101 uA - after: 86 uA	Selene ToyKeeper	1 year ago
676	updated D4Sv2-tintramp -> Emisar 2-channel build target ... updated D4Sv2-tintramp -> Emisar 2-channel build target ... ... and reworked how gradual_tick() works ... and updated LT1S Pro to use new method	Selene ToyKeeper	1 year ago
675	added stepped tint ramping added stepped tint ramping patch adapted from SammysHP: https://github.com/SammysHP/flashlight-firmware/commit/0df174a6f6cc2676703f55a9b86eb3d9b3896b33	Selene ToyKeeper	1 year ago
674	LT1S Pro: added white-only auto-tint mode, at gchart's reque... LT1S Pro: added white-only auto-tint mode, at gchart's request	Selene ToyKeeper	1 year ago
673	made "Ramp 3H" do momentary turbo if current channel mode ha... made "Ramp 3H" do momentary turbo if current channel mode has no args	Selene ToyKeeper	1 year ago
672	LT1S Pro: raised the ramp a bit; it seemed too low in the mi... LT1S Pro: raised the ramp a bit; it seemed too low in the middle	Selene ToyKeeper	1 year ago
671	switched the rest of FSM + Anduril to use SPDX license heade... switched the rest of FSM + Anduril to use SPDX license headers instead of full GPL headers (or all too often, nothing at all) There are a few "FIXME" entries where I'm not sure about the correct copyright.	Selene ToyKeeper	1 year ago
670	reduced ROM by ~600 bytes by moving all eeprom config values... reduced ROM by ~600 bytes by moving all eeprom config values to a "cfg" struct (this also made some parts of the code cleaner)	Selene ToyKeeper	1 year ago