1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
// Sofirn SP10 Pro config options for Anduril
// Copyright (C) 2022-2023 (FIXME)
// SPDX-License-Identifier: GPL-3.0-or-later
#pragma once
#define MODEL_NUMBER "0631"
#include "hwdef-Sofirn_SP10-Pro.h"
// ATTINY: 1616
// don't blink during the ramp or at the ceiling
#ifdef BLINK_AT_RAMP_MIDDLE
#undef BLINK_AT_RAMP_MIDDLE
#endif
#ifdef BLINK_AT_RAMP_CEIL
#undef BLINK_AT_RAMP_CEIL
#endif
#define USE_DYNAMIC_UNDERCLOCKING
// 1....15: level_calc.py 3.01 1 15 7135 1 0.1 2 --pwm dyn:15:64:64
// 16..150: level_calc.py 5.01 1 135 7135 1 2 800 --pwm dyn:49:3072:255:3.0
#define RAMP_LENGTH 150
#define USE_DYN_PWM
#define _PWM1_LEVELS_ 1,2,4,6,9,12,15,19,23,28,34,41,48,55,64
#define _PWM1_TOPS_ 64,64,64,64,64,64,64,64,64,64,64,64,64,64,64
#define _PWM2_LEVELS_ 1,1,2,2,3,3,4,4,5,5,6,6,6,7,7,7,7,7,7,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,9,9,9,10,10,10,11,11,12,13,13,14,15,15,16,17,18,18,19,20,21,22,23,24,25,26,27,28,29,30,31,33,34,35,37,38,39,41,42,44,46,47,49,51,53,55,57,59,61,63,65,67,70,72,74,77,79,82,85,88,90,93,96,99,103,106,109,113,116,120,123,127,131,135,139,143,147,151,156,160,165,170,175,180,185,190,195,201,206,212,218,223,230,236,242,248,255
#define _PWM2_TOPS_ 3072,1960,2372,1476,2097,1572,1920,1570,1777,1524,1646,1454,1286,1369,1234,1115,1011,918,837,894,823,759,702,650,603,560,522,487,455,425,398,374,351,330,310,292,275,259,280,265,251,266,253,240,252,240,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
#define PWM1_LEVELS _PWM1_LEVELS_,_PWM2_TOPS_
#define PWM2_LEVELS 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,_PWM2_LEVELS_
#define PWM_TOPS _PWM1_TOPS_,_PWM2_TOPS_
#define MAX_1x7135 15
#define HALFSPEED_LEVEL 15
#define QUARTERSPEED_LEVEL 15
#define DEFAULT_LEVEL 75
#define RAMP_SMOOTH_FLOOR 1
#define RAMP_SMOOTH_CEIL 150
// 1 25 50 [75] 100 125 150
#define RAMP_DISCRETE_FLOOR 1
#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL
#define RAMP_DISCRETE_STEPS 7
// at Sofirn's request, use max (150) for the Simple UI ceiling
// 15 48 [82] 116 150
#define SIMPLE_UI_FLOOR MAX_1x7135
#define SIMPLE_UI_CEIL 150
#define SIMPLE_UI_STEPS 5
// turn on at ~6 lm by default (level 50/150, or ramp step 2/5 or 3/7)
// (also sets lockout mode 2H to a useful level)
#define DEFAULT_MANUAL_MEMORY 50
// reset to default after being off for 10 minutes
#define DEFAULT_MANUAL_MEMORY_TIMER 10
// enable SOS in the blinkies group
#define USE_SOS_MODE
#define USE_SOS_MODE_IN_BLINKY_GROUP
// Allow 3C in Simple UI for switching between smooth and stepped ramping
#define USE_SIMPLE_UI_RAMPING_TOGGLE
// and finally, set the default ramp style to Stepped
#undef RAMP_STYLE
#define RAMP_STYLE 1 // 0 = smooth, 1 = stepped
// stop panicking at ~30% power
#define THERM_FASTER_LEVEL 105
#define MIN_THERM_STEPDOWN 65 // must be > end of dynamic PWM range
// slow down party strobe; this driver can't pulse for too short a time
//#define PARTY_STROBE_ONTIME 8
#define STROBE_OFF_LEVEL 1 // keep the regulator chip on between pulses
// the default of 26 looks a bit flat, so increase it
#define CANDLE_AMPLITUDE 50
// enable 2 click turbo (replaces USE_2C_MAX_TURBO)
#define DEFAULT_2C_STYLE 1
// enable factory reset on 13H without loosening tailcap
#define USE_SOFT_FACTORY_RESET
|