~toykeeper/flashlight-firmware/trunk

#ifndef HWDEF_NOCTIGON_K1SBT90_H

#define HWDEF_NOCTIGON_K1SBT90_H

/* Noctigon K1-SBT90.2 driver layout (attiny1634)

 * (mostly the same as KR4 driver)

 *

 * Pin / Name / Function

 *   1    PA6   FET PWM (direct drive) (PWM1B)

 *   2    PA5   R: red aux LED (PWM0B)

 *   3    PA4   G: green aux LED

 *   4    PA3   B: blue aux LED

 *   5    PA2   (none)

 *   6    PA1   (none)

 *   7    PA0   (none)

 *   8    GND   GND

 *   9    VCC   VCC

 *  10    PC5   (none)

 *  11    PC4   (none)

 *  12    PC3   RESET

 *  13    PC2   (none)

 *  14    PC1   SCK

 *  15    PC0   (none) PWM0A

 *  16    PB3   main LED PWM (linear) (PWM1A)

 *  17    PB2   MISO / e-switch (PCINT10)

 *  18    PB1   MOSI / battery voltage (ADC6)

 *  19    PB0   Opamp power

 *  20    PA7   (none)

 *      ADC12   thermal sensor

 *

 * Main LED power uses one pin to turn the Opamp on/off,

 * and one pin to control Opamp power level.

 * Main brightness control uses the power level pin, with 4 kHz 10-bit PWM.

 * The on/off pin is only used to turn the main LED on and off,

 * not to change brightness.

 * Also has a direct-drive FET for turbo.

 */

#ifdef ATTINY

#undef ATTINY

#endif

#define ATTINY 1634

#include <avr/io.h>

#define PWM_CHANNELS 2

#define PWM_BITS 10  // 0 to 1023 at 4 kHz, not 0 to 255 at 16 kHz

#define PWM_TOP 1023

#define SWITCH_PIN   PB2     // pin 17

#define SWITCH_PCINT PCINT10 // pin 17 pin change interrupt

#define SWITCH_PCIE  PCIE1   // PCIE1 is for PCINT[11:8]

#define SWITCH_PCMSK PCMSK1  // PCMSK1 is for PCINT[11:8]

#define SWITCH_PORT  PINB    // PINA or PINB or PINC

#define PCINT_vect   PCINT1_vect  // ISR for PCINT[11:8]

#define PWM1_PIN PB3        // pin 16, Opamp reference

#define PWM1_LVL OCR1A      // OCR1A is the output compare register for PB3

#define PWM2_PIN PA6        // pin 1, DD FET PWM

#define PWM2_LVL OCR1B      // OCR1B is the output compare register for PA6

#define LED_ENABLE_PIN  PB0    // pin 19, Opamp power

#define LED_ENABLE_PORT PORTB  // control port for PB0

#define USE_VOLTAGE_DIVIDER  // use a dedicated pin, not VCC, because VCC input is flattened

#define VOLTAGE_PIN PB1      // Pin 18 / PB1 / ADC6

// pin to ADC mappings are in DS table 19-4

#define VOLTAGE_ADC      ADC6D  // digital input disable pin for PB1

// DIDR0/DIDR1 mappings are in DS section 19.13.5, 19.13.6

#define VOLTAGE_ADC_DIDR DIDR1  // DIDR channel for ADC6D

// DS tables 19-3, 19-4

// Bit   7     6     5      4     3    2    1    0

//     REFS1 REFS0 REFEN ADC0EN MUX3 MUX2 MUX1 MUX0

// MUX[3:0] = 0, 1, 1, 0 for ADC6 / PB1

// divided by ...

// REFS[1:0] = 1, 0 for internal 1.1V reference

// other bits reserved

#define ADMUX_VOLTAGE_DIVIDER 0b10000110

#define ADC_PRSCL   0x07    // clk/128

// TODO: calibrate this

// Raw ADC readings at 4.4V and 2.2V

// calibrate the voltage readout here

// estimated / calculated values are:

//   (voltage - D1) * (R2/(R2+R1) * 256 / 1.1)

// D1, R1, R2 = 0, 330, 100

#ifndef ADC_44

//#define ADC_44 981  // raw value at 4.40V

#define ADC_44 967  // manually tweaked so 4.16V will blink out 4.2

#endif

#ifndef ADC_22

//#define ADC_22 489  // raw value at 2.20V

#define ADC_22 482  // manually tweaked so 4.16V will blink out 4.2

#endif

#define TEMP_CHANNEL 0b00001111

// this light has aux LEDs under the optic

#define AUXLED_R_PIN    PA5    // pin 2

#define AUXLED_G_PIN    PA4    // pin 3

#define AUXLED_B_PIN    PA3    // pin 4

#define AUXLED_RGB_PORT PORTA  // PORTA or PORTB or PORTC

#define AUXLED_RGB_DDR  DDRA   // DDRA or DDRB or DDRC

#define AUXLED_RGB_PUE  PUEA   // PUEA or PUEB or PUEC

// with so many pins, doing this all with #ifdefs gets awkward...

// ... so just hardcode it in each hwdef file instead

inline void hwdef_setup() {

  // enable output ports

  // Opamp level and Opamp on/off

  DDRB = (1 << PWM1_PIN)

       | (1 << LED_ENABLE_PIN);

  // DD FET PWM, aux R/G/B

  DDRA = (1 << PWM2_PIN)

       | (1 << AUXLED_R_PIN)

       | (1 << AUXLED_G_PIN)

       | (1 << AUXLED_B_PIN)

       ;

  // configure PWM

  // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter

  // pre-scale for timer: N = 1

  // WGM1[3:0]: 0,0,1,1: PWM, Phase Correct, 10-bit (DS table 12-5)

  // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)

  // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)

  // COM1B[1:0]:    1,0: PWM OC1B in the normal direction (DS table 12-4)

  TCCR1A  = (1<<WGM11)  | (1<<WGM10)   // 10-bit (TOP=0x03FF) (DS table 12-5)

          | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)

          | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)

          ;

  TCCR1B  = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)

          | (0<<WGM13)  | (0<<WGM12)  // phase-correct PWM (DS table 12-5)

          ;

  // set up e-switch

  //PORTB = (1 << SWITCH_PIN);  // TODO: configure PORTA / PORTB / PORTC?

  PUEB = (1 << SWITCH_PIN);  // pull-up for e-switch

  SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt

}

#define LAYOUT_DEFINED

#endif