1
/****************************************************************************************
2
* Setups_Spark_2C1S.h - for the Spark SF6, 2 channels, 1S battery
7
****************************************************************************************/
11
//----------------------------------------------------------------------------------------
12
// Driver Board Settings
13
//----------------------------------------------------------------------------------------
14
#define OUT_CHANNELS 2 // define the output channels as 1, 2 or 3
16
//#define TURBO_LEVEL_SUPPORT // set if you want a max turbo level above the max ramping level
18
#define VOLTAGE_MON // Comment out to disable - ramp down and eventual shutoff when battery is low
19
//#define VOLT_MON_R1R2 // uses external R1/R2 voltage divider, comment out for 1.1V internal ref
21
// For voltage monitoring on pin #7, only uncomment one of the two def's below:
22
//#define USING_220K // for using the 220K resistor
23
//#define USING_360K // for using a 360K resistor (LDO and 2S cells)
25
#define D1_DIODE 30 // Drop over rev. polarity protection diode: using 0.28V for Q8.
26
// Value is added to the reading: higher the #, higher it reads
28
// For 2 channel (FET+1) boards:
29
//#define USING_3807135_BANK // (default OFF) sets up ramping for 380 mA 7135's instead of a FET
31
// For 3 channel (triple) boards:
32
//#define TRIPLE_3_7135 // Configure for 3 7135's
33
//#define TRIPLE_8_7135 // Configure for 8 7135's
35
//#define ONBOARD_LED // Disable/Enable the LED support
37
//----------------------------------------------------------------------------------------
38
//----------------------------------------------------------------------------------------
41
//----------------------------------------------------------------------------------------
42
// Temperature Monitoring
43
//----------------------------------------------------------------------------------------
44
// Temperature Calibration Offset -
45
#define TEMP_CAL_OFFSET (4)
46
// 4 dead-on for the Spark SF6
47
// 1 about right for the C8F #1
48
// -12 guess for the JM70 #2
49
// -19 is about right for the Lumintop SD Mini, IOS proto driver
50
// -6 BLF Q8 Round 3 - blinks 29C w/3 setting for 20C (68F) room temp
51
// -2 try for the Manker U21 (LJ)
52
// -2 works for the Warsun X60 (robo) using the 17 mm DEL driver
53
// -1 try this for proto #1, OSHPark BLF Q8 driver
54
// 3 about right for BLF Q8 proto #2 and #3, reads ~20 for ~68F (18C)
55
// -12 this is about right on the DEL DDm-L4 board in the UranusFire C818 light
56
// -11 On the TA22 board in SupFire M2-Z, it's bout 11-12C too high,reads 35C at room temp, 23C=73.4F
57
// -8 For the Manker U11 - at -11, reads 18C at 71F room temp (22C)
58
// -2 For the Lumintop SD26 - at -2, reading a solid 19C-20C (66.2F-68F for 67F room temp)
60
#define DEFAULT_STEPDOWN_TEMP (55) // default for stepdown temperature (50C=122F, 55C=131F)
61
// use 50C for smaller size hosts, or a more conservative level (SD26, U11, etc.)
62
// use 55C to 60C for larger size hosts, maybe C8 and above, or for a more aggressive setting
64
#define TEMP_ADJ_PERIOD 2812 // Over Temp adjustment frequency: 45 secs (in 16 msec ticks)
65
//----------------------------------------------------------------------------------------
66
//----------------------------------------------------------------------------------------
69
//----------------------------------------------------------------------------------------
70
#ifndef VOLT_MON_R1R2 // if using R1/R2, change the LVP settings in the calibration header file
71
#define BATT_LOW 30 // Cell voltage to step light down = 3.0 V
72
#define BATT_CRIT 28 // Cell voltage to shut the light off = 2.8 V
74
//----------------------------------------------------------------------------------------
77
//----------------------------------------------------------------------------------------
78
// Stored Configuration Setting Defaults
79
//----------------------------------------------------------------------------------------
80
#define DEF_RAMPING 1 // 1: ramping, 0: mode sets
81
#if USING_3807135_BANK
82
#define DEF_MOON_LEVEL 5 // 0..7, 0: disabled, usually set to 3 (350 mA) or 5 (380 mA) - 2 might work on a 350 mA
84
#define DEF_MOON_LEVEL 2 // 0..7, 0: disabled, usually set to 3 (350 mA) or 5 (380 mA) - 2 might work on a 350 mA
86
#define DEF_STEPDOWN_MODE 5 // 0=disabled, 1=thermal, 2=60s, 3=90s, 4=120s, 5=3min, 6=5min, 7=7min (3 mins is good for production)
87
#define DEF_BLINKY_MODE 2 // blinky mode config: 1=strobe only, 2=all blinkies, 0=disable
89
#define DEF_MODE_SET_IDX 3 // 0..11, mode set currently in effect, chosen by user (3=4 modes)
90
#define DEF_MOON_MODE 1 // 1: enable moonlight mode, 0: disable moon mode
91
#define DEF_HIGH_TO_LOW 0 // 1: highest to lowest, 0: modes go from lowest to highest
92
#define DEF_MODE_MEMORY 0 // 1: save/recall last mode set, 0: no memory
94
#define DEF_LOCATOR_LED 1 // Locator LED feature (ON when light is OFF) - 1=enabled, 0=disabled
95
#define DEF_BVLD_LED_ONLY 0 // BVLD (Battery Voltage Level Display) - 1=BVLD shown only w/onboard LED, 0=both primary and onboard LED's
96
#define DEF_ONBOARD_LED 1 // On Board LED support - 1=enabled, 0=disabled
97
//----------------------------------------------------------------------------------------
98
//----------------------------------------------------------------------------------------
101
//----------------------------------------------------------------------------------------
102
// Operational Settings Enable/Disable
103
//----------------------------------------------------------------------------------------
104
#define STARTUP_LIGHT_OFF // (default ON) for ramping from power up, main light OFF, otherwise set to max
105
#define STARTUP_2BLINKS // enables the powerup/startup two blinks
106
#define LOCKOUT_ENABLE // (default ON) Enable the "Lock-Out" feature
107
#define TRIPLE_CLICK_BATT // (default ON) enable a triple-click to display Battery status
108
#define RAMPING_REVERSE // (default ON) reverses ramping direction for every click&hold
109
#define OFFTIME_ENABLE 0 // 1: Do OFF time mode memory for Mode Sets on power switching (tailswitch), 0: disabled
111
//#define BLINK_ONLY_IND_LED // blink the Ind. LED, not main LED for: startup, config settings, Enter/Exit lockout blinks
112
//#define ADV_RAMP_OPTIONS // In ramping, enables "mode set" additional method for lock-out and battery voltage display, comment out to disable
113
//----------------------------------------------------------------------------------------
114
//----------------------------------------------------------------------------------------
117
//----------------------------------------------------------------------------------------
119
//----------------------------------------------------------------------------------------
120
#define RAMP_SWITCH_TIMEOUT 75 // make the up/dn ramp switch timeout 1.2 secs (same as IDLE_TIME)
122
#define STROBE_SPEED 14,41 // 14,41: 18Hz, 16,47: 16Hz, 20,60: 12.5Hz
124
#define SHORT_CLICK_DUR 18 // Short click max duration - for 0.288 secs
125
#define RAMP_MOON_PAUSE 23 // this results in a 0.368 sec delay, paused in moon mode
127
// One-Click Turn OFF option:
128
#define IDLE_TIME 75 // make the time-out 1.2 seconds (Comment out to disable)
131
#define LONG_PRESS_DUR 24 // Prev Mode time - long press, 24=0.384s (1/3s: too fast, 0.5s: too slow)
132
#define XLONG_PRESS_DUR 75 // strobe mode entry hold time - 75=1.2s, 68=1.09s (any slower it can happen unintentionally too much)
133
#define CONFIG_ENTER_DUR 200 // In Mode Sets Only: Config mode entry hold time - 200=3.2s, 160=2.5s
135
#define DBL_CLICK_TICKS 14 // fast click time for enable/disable of Lock-Out, batt check,
136
// and double/triple click timing (14=0.224s, was 16=0.256s)
138
#define ADC_DELAY 312 // Delay in ticks between low-batt ramp-downs (312=5secs, was 250=4secs)
139
//----------------------------------------------------------------------------------------
140
//----------------------------------------------------------------------------------------
143
//----------------------------------------------------------------------------------------
144
// Strobe/Blinky mode Configuration
145
//----------------------------------------------------------------------------------------
146
#define BATT_CHECK_MODE 80
147
#define TEMP_CHECK_MODE 81
148
#define FIRM_VERS_MODE 82
149
#define SPECIAL_MODES 90 // base/lowest value for special modes
150
#define STROBE_MODE SPECIAL_MODES+1
151
//#define RANDOM_STROBE SPECIAL_MODES+2 // not used for now...
152
#define POLICE_STROBE SPECIAL_MODES+2
153
#define BIKING_STROBE SPECIAL_MODES+3
154
#define BEACON_2S_MODE SPECIAL_MODES+4
155
#define BEACON_10S_MODE SPECIAL_MODES+5
157
// Custom define your blinky mode set here:
158
#define SPECIAL_MODES_SET STROBE_MODE, POLICE_STROBE, BIKING_STROBE, BEACON_2S_MODE, BEACON_10S_MODE
159
//----------------------------------------------------------------------------------------
160
//----------------------------------------------------------------------------------------
162
#endif /* SETTINGS_H_ */
b'\\ No newline at end of file'
added
removed
Tom_E/narsil/NarsilMulti/Setups_Spark_2C1S.h
