1
diff -u tools/hciattach.8 tools/hciattach.8
2
--- tools/hciattach.8 2004-05-09 11:39:43.000000000 +0100
3
+++ tools/hciattach.8 2004-05-26 13:02:35.000000000 +0100
5
hciattach \- attach serial devices via UART HCI to BlueZ stack
8
-[ -n ] [ -p ] [ -t timeout ] <
26
Hciattach is used to attach a serial UART to the Bluetooth stack as HCI
32
Don't detach from controlling terminal.
36
Print the PID when detaching.
40
Specify an initialization timeout. (Default is 5 seconds.)
44
This specifies the serial device to attach. A leading
46
can be omitted. Examples:
58
of the Bluetooth device that is to be attached, i.e. vendor or other device
59
specific identifier. Currently supported types are
67
Unspecified HCI_UART interface, no vendor specific options
71
Ericsson based modules
75
Digianswer based cards
79
Xircom PCMCIA cards: Credit Card Adapter and Real Port Adapter
83
CSR Casira serial adapter or BrainBoxes serial dongle (BL642)
87
BrainBoxes PCMCIA card (BL620)
95
Serial adapters using CSR chips with BCSP serial protocol
98
Supported IDs are (manufacturer id, product id)
103
Xircom PCMCIA cards: Credit Card Adapter and Real Port Adapter
107
BrainBoxes PCMCIA card (BL620)
116
specifies the UART speed to use. Baudrates higher than 115.200bps require
117
vendor specific initializations that are not implemented for all types of
118
devices. In general the following speeds are supported:
120
Supported vendor devices are automatically initialised to their respective
128
is appended to the list of options then hardware flow control is forced on
131
diff -u tools/hciconfig.8 tools/hciconfig.8
132
--- tools/hciconfig.8 2004-05-09 11:39:43.000000000 +0100
133
+++ tools/hciconfig.8 2004-05-26 13:02:35.000000000 +0100
136
hciconfig \- configure Bluetooth devices
146
-.B hciconfig [-a] <hciX> [command [command parameters]]
150
+.RI [\| "command parameters" \|]\|]
156
-is used to configure Bluetooth devices. <hciX> is the name of a Bluetooth
157
-device installed in the system. If <hciX> is not given,
161
+is used to configure Bluetooth devices.
163
+is the name of a Bluetooth device installed in the system. If
167
prints name and basic information about all the Bluetooth devices installed in
168
-the system. If <hciX> is given but no command is given,
169
-it prints basic information on device <hciX> only. Basic information is
172
+is given but no command is given, it prints basic information on device
174
+only. Basic information is
175
interface type, BD address, ACL MTU, SCO MTU, flags (up, init, running, raw,
176
page scan enabled, inquiry scan enabled, inquiry, authentication enabled,
182
Gives a list of possible commands
186
Other than the basic info, print features, packet type, link policy, link mode,
187
name, class, version.
192
Open and initialize HCI device
204
Reset statistic counters
208
Enable authentication
212
Disable authentication
224
Enable page and inquiry scan
228
Disable page and inquiry scan
232
Enable inquiry scan, disable page scan
236
Enable page scan, disable inquiry scan
239
+\fBptype\fP [\fItype\fP]
244
, displays the current packet types. Otherwise, all the packet types specified
253
is a comma-separated list of packet types, where the possible packet types are
258
prints voice setting. Otherwise, sets voice setting to
263
is a 16-bit hex number describing the voice setting.
267
prints out the current inquiry mode. Otherwise, sets inquiry mode to
270
-.BI inqparms " [win:int]"
271
+\fBinqparams\fP [\fIwin\fP:\fIint\fP]
275
prints inquiry scan window and interval. Otherwise, sets inquiry scan window
278
@@ -137,23 +142,20 @@
282
-.BI pageparms " [win:int]"
283
+\fBpageparms\fP [\fIwin\fP:\fIint\fP]
287
prints page scan window and interval. Otherwise, sets page scan window to
291
slots and page scan interval to
300
prints page timeout. Otherwise, sets page timeout
307
@@ -163,19 +165,16 @@
308
prints out the current AFH mode. Otherwise, sets AFH mode to
311
-.BI aclmtu " <mtu:pkt>"
312
+\fBaclmtu\fP \fImtu\fP:\fIpkt\fP
318
bytes and ACL buffer size to
324
-.BI scomtu " <mtu:pkt>"
325
+\fBscomtu\fP \fImtu\fP:\fIpkt\fP
329
bytes and SCO buffer size to
331
@@ -192,43 +191,34 @@
346
mean, respectively, to ask to become master or to remain slave when a
347
connection request comes in. The additional keyword
351
means that baseband connections will be accepted even if there are no
360
or a comma-separated list of keywords, where possible keywords are
369
sets link policy to the default behaviour of remaining slave and not accepting
370
baseband connections when there are no listening
376
is present, the device will ask to become master if a connection request comes
381
is present, the device will accept baseband connections even when there are no
384
diff -u tools/l2ping.1 tools/l2ping.1
385
--- tools/l2ping.1 2004-05-09 11:39:43.000000000 +0100
386
+++ tools/l2ping.1 2004-05-26 13:02:35.000000000 +0100
388
l2ping \- Send L2CAP echo request and receive answer
401
+.IR source\-addr \|]
412
L2ping sends a L2CAP echo request to the Bluetooth MAC address
415
given in dotted hex notation.
419
+.BI \-S " source\-addr"
420
Select address to be used as source address for the request.
427
of the data packets to be sent.
434
number of packets then exit.
438
Kind of flood ping. Use with care! It reduces the delay time between packets