1
# Port on which the server is listening. You must select a different
2
# port from your standard HTTP web server if it is running on the same
6
# Address on which the server is bound. Only useful if you have
7
# several network interfaces.
10
# Number of simultaneous HTTP connections that can be handled. It has
11
# to be defined *before* the MaxClients parameter, since it defines the
12
# MaxClients maximum limit.
13
MaxHTTPConnections 2000
15
# Number of simultaneous requests that can be handled. Since AVServer
16
# is very fast, it is more likely that you will want to leave this high
17
# and use MaxBandwidth, below.
20
# This the maximum amount of kbit/sec that you are prepared to
21
# consume when streaming to clients.
24
# Access log file (uses standard Apache log file format)
25
# '-' is the standard output.
28
# Suppress that if you want to launch avserver as a daemon.
32
##################################################################
33
# Definition of the live feeds. Each live feed contains one video
34
# and/or audio sequence coming from an ffmpeg encoder or another
35
# avserver. This sequence may be encoded simultaneously with several
36
# codecs at several resolutions.
40
# You must use 'ffmpeg' to send a live feed to avserver. In this
41
# example, you can type:
43
# ffmpeg http://localhost:8090/feed1.ffm
45
# avserver can also do time shifting. It means that it can stream any
46
# previously recorded live stream. The request should contain:
47
# "http://xxxx?date=[YYYY-MM-DDT][[HH:]MM:]SS[.m...]".You must specify
48
# a path where the feed is stored on disk. You also specify the
49
# maximum size of the feed, where zero means unlimited. Default:
50
# File=/tmp/feed_name.ffm FileMaxSize=5M
55
# ReadOnlyFile /saved/specialvideo.ffm
56
# This marks the file as readonly and it will not be deleted or updated.
58
# Specify launch in order to start ffmpeg automatically.
59
# First ffmpeg must be defined with an appropriate path if needed,
60
# after that options can follow, but avoid adding the http:// field
63
# Only allow connections from localhost to the feed.
69
##################################################################
70
# Now you can define each stream which will be generated from the
71
# original audio and video stream. Each format has a filename (here
72
# 'test1.mpg'). AVServer will send this stream when answering a
73
# request containing this filename.
77
# coming from live feed 'feed1'
80
# Format of the stream : you can choose among:
81
# mpeg : MPEG-1 multiplexed video and audio
82
# mpegvideo : only MPEG-1 video
83
# mp2 : MPEG-2 audio (use AudioCodec to select layer 2 and 3 codec)
84
# ogg : Ogg format (Vorbis audio codec)
85
# rm : RealNetworks-compatible stream. Multiplexed audio and video.
86
# ra : RealNetworks-compatible stream. Audio only.
87
# mpjpeg : Multipart JPEG (works with Netscape without any plugin)
88
# jpeg : Generate a single JPEG image.
89
# asf : ASF compatible streaming (Windows Media Player format).
90
# swf : Macromedia Flash compatible stream
91
# avi : AVI format (MPEG-4 video, MPEG audio sound)
94
# Bitrate for the audio stream. Codecs usually support only a few
98
# Number of audio channels: 1 = mono, 2 = stereo
101
# Sampling frequency for audio. When using low bitrates, you should
102
# lower this frequency to 22050 or 11025. The supported frequencies
103
# depend on the selected audio codec.
104
AudioSampleRate 44100
106
# Bitrate for the video stream
109
# Ratecontrol buffer size
112
# Number of frames per second
115
# Size of the video frame: WxH (default: 160x128)
116
# The following abbreviations are defined: sqcif, qcif, cif, 4cif, qqvga,
117
# qvga, vga, svga, xga, uxga, qxga, sxga, qsxga, hsxga, wvga, wxga, wsxga,
118
# wuxga, woxga, wqsxga, wquxga, whsxga, whuxga, cga, ega, hd480, hd720,
122
# Transmit only intra frames (useful for low bitrates, but kills frame rate).
125
# If non-intra only, an intra frame is transmitted every VideoGopSize
126
# frames. Video synchronization can only begin at an intra frame.
129
# More MPEG-4 parameters
133
# Choose your codecs:
135
#VideoCodec mpeg1video
146
# Set this to the number of seconds backwards in time to start. Note that
147
# most players will buffer 5-10 seconds of video, and also you need to allow
148
# for a keyframe to appear in the data stream.
153
# You can allow ranges of addresses (or single addresses)
154
#ACL ALLOW <first address> <last address>
156
# You can deny ranges of addresses (or single addresses)
157
#ACL DENY <first address> <last address>
159
# You can repeat the ACL allow/deny as often as you like. It is on a per
160
# stream basis. The first match defines the action. If there are no matches,
161
# then the default is the inverse of the last ACL statement.
163
# Thus 'ACL allow localhost' only allows access from localhost.
164
# 'ACL deny 1.0.0.0 1.255.255.255' would deny the whole of network 1 and
165
# allow everybody else.
170
##################################################################
233
#AudioSampleRate 44100
242
#Title "Stream title"
245
#AudioSampleRate 44100
250
# Real with audio only at 32 kbits
261
# Real with audio and video at 64 kbits
274
##################################################################
275
# A stream coming from a file: you only need to set the input
276
# filename and optionally a new format. Supported conversions:
280
#File "/usr/local/httpd/htdocs/tlive.rm"
285
#File "/usr/local/httpd/htdocs/test.asf"
288
#Copyright "Super MegaCorp"
289
#Title "Test stream from disk"
290
#Comment "Test comment"
294
##################################################################
297
# You can access this stream with the RTSP URL:
298
# rtsp://localhost:5454/test1-rtsp.mpg
300
# A non-standard RTSP redirector is also created. Its URL is:
301
# http://localhost:8090/test1-rtsp.rtsp
303
#<Stream test1-rtsp.mpg>
305
#File "/usr/local/httpd/htdocs/test1.mpg"
309
# Transcode an incoming live feed to another live feed,
310
# using libx264 and video presets
319
#AVPresetVideo default
320
#AVPresetVideo baseline
321
#AVOptionVideo flags +global_header
326
#AudioSampleRate 22050
327
#AVOptionAudio flags +global_header
330
##################################################################
331
# SDP/multicast examples
333
# If you want to send your stream in multicast, you must set the
334
# multicast address with MulticastAddress. The port and the TTL can
337
# An SDP file is automatically generated by avserver by adding the
338
# 'sdp' extension to the stream name (here
339
# http://localhost:8090/test1-sdp.sdp). You should usually give this
340
# file to your player to play the stream.
342
# The 'NoLoop' option can be used to avoid looping when the stream is
345
#<Stream test1-sdp.mpg>
347
#File "/usr/local/httpd/htdocs/test1.mpg"
348
#MulticastAddress 224.124.0.1
355
##################################################################
363
# Only allow local people to get the status
365
ACL allow 192.168.0.0 192.168.255.255
367
#FaviconURL http://pond1.gladstonefamily.net:8080/favicon.ico
371
# Redirect index.html to the appropriate site
373
<Redirect index.html>
374
URL http://www.libav.org/
added
removed
doc/avserver.conf
