2
* Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved.
4
* Redistribution and use in source and binary forms, with or without
5
* modification, are permitted provided that the following conditions are
6
* met: 1. Redistributions of source code must retain the above copyright
7
* notice, this list of conditions and the following disclaimer. 2. The name
8
* of the author may not be used to endorse or promote products derived from
9
* this software without specific prior written permission
11
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED
12
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
13
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
14
* EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
15
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
16
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
17
* PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
18
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
19
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
20
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
24
Modified by: Andres Vega Garcia
26
INRIA - Sophia Antipolis, France
27
e-mail: avega@sophia.inria.fr
28
finger: avega@pax.inria.fr
33
* Created from if_epreg.h by Fred Gray (fgray@rice.edu) to support the
38
* Modified by Shusuke Nisiyama <shu@athena.qe.eng.hokudai.ac.jp>
44
* Ethernet software status per interface.
48
* Some global constants
51
#define TX_INIT_RATE 16
52
#define TX_INIT_MAX_RATE 64
53
#define RX_INIT_LATENCY 64
54
#define RX_INIT_EARLY_THRESH 64
55
#define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */
56
#define MIN_RX_EARLY_THRESHL 4
58
#define EEPROMSIZE 0x40
59
#define MAX_EEPROMBUSY 1000
60
#define VX_LAST_TAG 0xd7
61
#define VX_MAX_BOARDS 16
62
#define VX_ID_PORT 0x100
65
* some macros to acces long named fields
67
#define BASE (eth_nic_base)
70
* Commands to read/write EEPROM trough EEPROM command register (Window 0,
73
#define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */
74
#define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */
75
#define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */
76
#define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */
78
#define EEPROM_BUSY (1<<15)
81
* Some short functions, worth to let them be a macro
84
/**************************************************************************
86
* These define the EEPROM data structure. They are used in the probe
87
* function to verify the existence of the adapter after having sent
90
* There are others but only the ones we use are defined here.
92
**************************************************************************/
94
#define EEPROM_NODE_ADDR_0 0x0 /* Word */
95
#define EEPROM_NODE_ADDR_1 0x1 /* Word */
96
#define EEPROM_NODE_ADDR_2 0x2 /* Word */
97
#define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */
98
#define EEPROM_MFG_ID 0x7 /* 0x6d50 */
99
#define EEPROM_ADDR_CFG 0x8 /* Base addr */
100
#define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */
101
#define EEPROM_OEM_ADDR_0 0xa /* Word */
102
#define EEPROM_OEM_ADDR_1 0xb /* Word */
103
#define EEPROM_OEM_ADDR_2 0xc /* Word */
104
#define EEPROM_SOFT_INFO_2 0xf /* Software information 2 */
106
#define NO_RX_OVN_ANOMALY (1<<5)
108
/**************************************************************************
110
* These are the registers for the 3Com 3c509 and their bit patterns when *
111
* applicable. They have been taken out the the "EtherLink III Parallel *
112
* Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual *
115
**************************************************************************/
117
#define VX_COMMAND 0x0e /* Write. BASE+0x0e is always a
119
#define VX_STATUS 0x0e /* Read. BASE+0x0e is always status
121
#define VX_WINDOW 0x0f /* Read. BASE+0x0f is always window
124
* Window 0 registers. Setup.
127
#define VX_W0_EEPROM_DATA 0x0c
128
#define VX_W0_EEPROM_COMMAND 0x0a
129
#define VX_W0_RESOURCE_CFG 0x08
130
#define VX_W0_ADDRESS_CFG 0x06
131
#define VX_W0_CONFIG_CTRL 0x04
133
#define VX_W0_PRODUCT_ID 0x02
134
#define VX_W0_MFG_ID 0x00
138
* Window 1 registers. Operating Set.
141
#define VX_W1_TX_PIO_WR_2 0x02
142
#define VX_W1_TX_PIO_WR_1 0x00
144
#define VX_W1_FREE_TX 0x0c
145
#define VX_W1_TX_STATUS 0x0b /* byte */
146
#define VX_W1_TIMER 0x0a /* byte */
147
#define VX_W1_RX_STATUS 0x08
148
#define VX_W1_RX_PIO_RD_2 0x02
149
#define VX_W1_RX_PIO_RD_1 0x00
152
* Window 2 registers. Station Address Setup/Read
155
#define VX_W2_ADDR_5 0x05
156
#define VX_W2_ADDR_4 0x04
157
#define VX_W2_ADDR_3 0x03
158
#define VX_W2_ADDR_2 0x02
159
#define VX_W2_ADDR_1 0x01
160
#define VX_W2_ADDR_0 0x00
163
* Window 3 registers. FIFO Management.
166
#define VX_W3_INTERNAL_CFG 0x00
167
#define VX_W3_RESET_OPT 0x08
168
#define VX_W3_FREE_TX 0x0c
169
#define VX_W3_FREE_RX 0x0a
172
* Window 4 registers. Diagnostics.
175
#define VX_W4_MEDIA_TYPE 0x0a
176
#define VX_W4_CTRLR_STATUS 0x08
177
#define VX_W4_NET_DIAG 0x06
178
#define VX_W4_FIFO_DIAG 0x04
179
#define VX_W4_HOST_DIAG 0x02
180
#define VX_W4_TX_DIAG 0x00
183
* Window 5 Registers. Results and Internal status.
186
#define VX_W5_READ_0_MASK 0x0c
187
#define VX_W5_INTR_MASK 0x0a
188
#define VX_W5_RX_FILTER 0x08
189
#define VX_W5_RX_EARLY_THRESH 0x06
190
#define VX_W5_TX_AVAIL_THRESH 0x02
191
#define VX_W5_TX_START_THRESH 0x00
194
* Window 6 registers. Statistics.
197
#define TX_TOTAL_OK 0x0c
198
#define RX_TOTAL_OK 0x0a
199
#define TX_DEFERRALS 0x08
200
#define RX_FRAMES_OK 0x07
201
#define TX_FRAMES_OK 0x06
202
#define RX_OVERRUNS 0x05
203
#define TX_COLLISIONS 0x04
204
#define TX_AFTER_1_COLLISION 0x03
205
#define TX_AFTER_X_COLLISIONS 0x02
206
#define TX_NO_SQE 0x01
207
#define TX_CD_LOST 0x00
209
/****************************************
211
* Register definitions.
213
****************************************/
216
* Command register. All windows.
219
* 15-11: 5-bit code for command to be executed.
220
* 10-0: 11-bit arg if any. For commands with no args;
221
* this can be set to anything.
223
#define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms
225
#define WINDOW_SELECT (unsigned short) (0x1<<11)
226
#define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to
230
* before using trans-
232
#define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on
234
#define RX_ENABLE (unsigned short) (0x4<<11)
235
#define RX_RESET (unsigned short) (0x5<<11)
236
#define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11)
237
#define TX_ENABLE (unsigned short) (0x9<<11)
238
#define TX_DISABLE (unsigned short) (0xa<<11)
239
#define TX_RESET (unsigned short) (0xb<<11)
240
#define REQ_INTR (unsigned short) (0xc<<11)
242
* The following C_* acknowledge the various interrupts. Some of them don't
243
* do anything. See the manual.
245
#define ACK_INTR (unsigned short) (0x6800)
246
# define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1)
247
# define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2)
248
# define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4)
249
# define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8)
250
# define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10)
251
# define C_RX_EARLY (unsigned short) (ACK_INTR|0x20)
252
# define C_INT_RQD (unsigned short) (ACK_INTR|0x40)
253
# define C_UPD_STATS (unsigned short) (ACK_INTR|0x80)
254
#define SET_INTR_MASK (unsigned short) (0xe<<11)
255
#define SET_RD_0_MASK (unsigned short) (0xf<<11)
256
#define SET_RX_FILTER (unsigned short) (0x10<<11)
257
# define FIL_INDIVIDUAL (unsigned short) (0x1)
258
# define FIL_MULTICAST (unsigned short) (0x02)
259
# define FIL_BRDCST (unsigned short) (0x04)
260
# define FIL_PROMISC (unsigned short) (0x08)
261
#define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11)
262
#define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11)
263
#define SET_TX_START_THRESH (unsigned short) (0x13<<11)
264
#define STATS_ENABLE (unsigned short) (0x15<<11)
265
#define STATS_DISABLE (unsigned short) (0x16<<11)
266
#define STOP_TRANSCEIVER (unsigned short) (0x17<<11)
269
* Status register. All windows.
271
* 15-13: Window number(0-7).
272
* 12: Command_in_progress.
277
* 7: Update Statistics.
278
* 6: Interrupt Requested.
283
* 1: Adapter Failure.
284
* 0: Interrupt Latch.
286
#define S_INTR_LATCH (unsigned short) (0x1)
287
#define S_CARD_FAILURE (unsigned short) (0x2)
288
#define S_TX_COMPLETE (unsigned short) (0x4)
289
#define S_TX_AVAIL (unsigned short) (0x8)
290
#define S_RX_COMPLETE (unsigned short) (0x10)
291
#define S_RX_EARLY (unsigned short) (0x20)
292
#define S_INT_RQD (unsigned short) (0x40)
293
#define S_UPD_STATS (unsigned short) (0x80)
294
#define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000)
296
#define VX_BUSY_WAIT while (inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS)
298
/* Address Config. Register.
302
#define ACF_CONNECTOR_BITS 14
303
#define ACF_CONNECTOR_UTP 0
304
#define ACF_CONNECTOR_AUI 1
305
#define ACF_CONNECTOR_BNC 3
307
#define INTERNAL_CONNECTOR_BITS 20
308
#define INTERNAL_CONNECTOR_MASK 0x01700000
311
* FIFO Registers. RX Status.
313
* 15: Incomplete or FIFO empty.
314
* 14: 1: Error in RX Packet 0: Incomplete or no error.
315
* 13-11: Type of error.
317
* 1011 = Run Packet Error.
318
* 1100 = Alignment Error.
320
* 1001 = Oversize Packet Error (>1514 bytes)
321
* 0010 = Dribble Bits.
322
* (all other error codes, no errors.)
324
* 10-0: RX Bytes (0-1514)
326
#define ERR_INCOMPLETE (unsigned short) (0x8000)
327
#define ERR_RX (unsigned short) (0x4000)
328
#define ERR_MASK (unsigned short) (0x7800)
329
#define ERR_OVERRUN (unsigned short) (0x4000)
330
#define ERR_RUNT (unsigned short) (0x5800)
331
#define ERR_ALIGNMENT (unsigned short) (0x6000)
332
#define ERR_CRC (unsigned short) (0x6800)
333
#define ERR_OVERSIZE (unsigned short) (0x4800)
334
#define ERR_DRIBBLE (unsigned short) (0x1000)
339
* Reports the transmit status of a completed transmission. Writing this
340
* register pops the transmit completion stack.
342
* Window 1/Port 0x0b.
345
* 6: Interrupt on successful transmission requested.
346
* 5: Jabber Error (TP Only, TX Reset required. )
347
* 4: Underrun (TX Reset required. )
348
* 3: Maximum Collisions.
349
* 2: TX Status Overflow.
353
#define TXS_COMPLETE 0x80
354
#define TXS_INTR_REQ 0x40
355
#define TXS_JABBER 0x20
356
#define TXS_UNDERRUN 0x10
357
#define TXS_MAX_COLLISION 0x8
358
#define TXS_STATUS_OVERFLOW 0x4
360
#define RS_AUI (1<<5)
361
#define RS_BNC (1<<4)
362
#define RS_UTP (1<<3)
366
#define RS_MII (1<<6)
370
* FIFO Status (Window 4)
372
* Supports FIFO diagnostics
374
* Window 4/Port 0x04.1
376
* 15: 1=RX receiving (RO). Set when a packet is being received
379
* 13: 1=RX underrun (RO). Generates Adapter Failure interrupt.
380
* Requires RX Reset or Global Reset command to recover.
381
* It is generated when you read past the end of a packet -
382
* reading past what has been received so far will give bad
384
* 12: 1=RX status overrun (RO). Set when there are already 8
385
* packets in the RX FIFO. While this bit is set, no additional
386
* packets are received. Requires no action on the part of
387
* the host. The condition is cleared once a packet has been
388
* read out of the RX FIFO.
389
* 11: 1=RX overrun (RO). Set when the RX FIFO is full (there
390
* may not be an overrun packet yet). While this bit is set,
391
* no additional packets will be received (some additional
392
* bytes can still be pending between the wire and the RX
393
* FIFO). Requires no action on the part of the host. The
394
* condition is cleared once a few bytes have been read out
396
* 10: 1=TX overrun (RO). Generates adapter failure interrupt.
397
* Requires TX Reset or Global Reset command to recover.
398
* Disables Transmitter.
400
* 7-0: Built in self test bits for the RX and TX FIFO's.
402
#define FIFOS_RX_RECEIVING (unsigned short) 0x8000
403
#define FIFOS_RX_UNDERRUN (unsigned short) 0x2000
404
#define FIFOS_RX_STATUS_OVERRUN (unsigned short) 0x1000
405
#define FIFOS_RX_OVERRUN (unsigned short) 0x0800
406
#define FIFOS_TX_OVERRUN (unsigned short) 0x0400
409
* Misc defines for various things.
411
#define TAG_ADAPTER 0xd0
412
#define ACTIVATE_ADAPTER_TO_CONFIG 0xff
413
#define ENABLE_DRQ_IRQ 0x0001
414
#define MFG_ID 0x506d /* `TCM' */
415
#define PROD_ID 0x5090
416
#define GO_WINDOW(x) outw(WINDOW_SELECT|(x),BASE+VX_COMMAND)
417
#define JABBER_GUARD_ENABLE 0x40
418
#define LINKBEAT_ENABLE 0x80
419
#define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE)
420
#define DISABLE_UTP 0x0
421
#define RX_BYTES_MASK (unsigned short) (0x07ff)
422
#define RX_ERROR 0x4000
423
#define RX_INCOMPLETE 0x8000
424
#define TX_INDICATE 1<<15
425
#define is_eeprom_busy(b) (inw((b)+VX_W0_EEPROM_COMMAND)&EEPROM_BUSY)
427
#define VX_IOSIZE 0x20
429
#define VX_CONNECTORS 8
added
removed
src/grub4dos/netboot/.svn/text-base/3c595.h.svn-base
