5
.\" Process this file with
6
.\" groff -man -Tascii divaload.man for ASCII output, or
7
.\" groff -man -Tps divaload.man for PostScript output
9
.TH DIVALOAD 8 "2000/12/02" divaload "Linux System Administration"
11
divaload \- configure Eicon Diva active ISDN card
13
divaload controller protocol [options]
16
is used to setup the Eicon Diva card for the proper configuration.
20
selects the controller (card). This can be either:
26
is the controller number, or
30
to operate on all cards.
34
can be one of the following:
36
-f 1TR6 Germany, old protocol for PABX................ PRI & BRI
37
-f ETSI DSS1, Europe (Germany, ...)................... PRI & BRI
38
-f FRANC VN3, France, old protocol for PABX............ PRI & BRI
39
-f BELG NET3, Belgien, old protocol for PABX.......... PRI & BRI
40
-f SWED DSS1 with CRC4 off, Sweden, Benelux........... PRI
41
-f NI NI1, NI2, North America, National ISDN........ PRI & BRI
42
-f 5ESS 5ESS, North America, AT&T..................... PRI & BRI
43
-f JAPAN Japan, INS-NET64.............................. PRI & BRI
44
-f ATEL ATEL, Australia, old TPH1962.................. PRI & BRI
45
-f US North America, Auto Detect.................... BRI
46
-f ITALY DSS1, Italy................................... PRI & BRI
47
-f TWAN DSS1, Taiwan.................................. PRI & BRI
48
-f AUSTRAL Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI
49
-f 4ESS_SDN 4ESS Software Defined Network................. PRI
50
-f 4ESS_SDS 4ESS Switched Digital Service................. PRI
51
-f 4ESS_LDS 4ESS Long Distance Service.................... PRI
52
-f 4ESS_MGC 4ESS Megacom.................................. PRI
53
-f 4ESS_MGI 4ESS Megacom International.................... PRI
54
-f HONGKONG Hongkong...................................... PRI & BRI
55
-f RBSCAS Robbed Bit Signaling, CAS..................... PRI
56
-f QSIG QSIG, Intra PABX link protocol................ PRI & BRI
65
set Layer 1 framing on PRI Adapter
69
- doubleframing (NO CRC4)
79
set PRI Adapter in NT mode;
83
set PRI Adapter in High Impedance state
84
until first user application does request
88
set starting channel number on PRI Adapter.
89
By default the allocation of channels is made
90
on a high-to-low basis.
91
By specifying -l you select a low-to-high
92
allocation policy (in addition)
99
- CR and CHI 2 Bytes long (default)
102
- CR 1 byte, CHI 2 bytes
105
- CR is 2 bytes, CHI is 1 byte
110
(CR - Call Reference, CHI - B-Channel Ident.)
113
.BI "-n [" "0...20" ]
114
select NT2 mode and default length of DIDN
115
(DIDN - Direct Inward Dial Number)
118
turn off order checking of information elements
121
establish a permanent connection
122
(e.g. leased line configuration)
126
- TE <-> TE mode, structured line
129
- NT <-> TE mode, raw line
132
.BI "-s [" "0,1,2,3" ]
133
D-Channel Layer 2 activation policy on BRI Adapter
140
- Deactivation only by NT side, preferred, default
146
- Always active, mode 2
150
.BI "-t [" "0...63" ]
151
specifies a fixed TEI value
152
(Default is a automatic TEI assignment)
156
select point to point mode on BRI Adapter;
157
uses default TEI '0',
161
.BI "-[" "1...8" ]oad|osa|spid
162
BRI Adapter B-Channel options
163
Specify the Originating Address (OAD),
164
Originating Sub-address (OSA) and/or
165
Service Profile Identifier (SPID)
166
for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)
168
Example: -1oad 123456 -1spid 1234560001
172
display protocol options summary
176
select alternative protocol code directory.
178
default directory: "/usr/share/isdn"
181
.BI "-h "\fRor\fB " -?"
186
manpage written from -h output by Paul Slootman <paul@debian.org>.