2
* U-boot - Configuration file for cm-bf548 board
5
#ifndef __CONFIG_CM_BF548_H__
6
#define __CONFIG_CM_BF548_H__
8
#include <asm/config-pre.h>
14
#define CONFIG_BFIN_CPU bf548-0.0
15
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA
20
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
21
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
23
/* CONFIG_CLKIN_HZ is any value in Hz */
24
#define CONFIG_CLKIN_HZ 25000000
25
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
27
#define CONFIG_CLKIN_HALF 0
28
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
30
#define CONFIG_PLL_BYPASS 0
31
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
32
/* Values can range from 0-63 (where 0 means 64) */
33
#define CONFIG_VCO_MULT 21
34
/* CCLK_DIV controls the core clock divider */
35
/* Values can be 1, 2, 4, or 8 ONLY */
36
#define CONFIG_CCLK_DIV 1
37
/* SCLK_DIV controls the system clock divider */
38
/* Values can range from 1-15 */
39
#define CONFIG_SCLK_DIV 4
41
/* Decrease core voltage */
42
#define CONFIG_VR_CTL_VAL (VLEV_115 | GAIN_20 | FREQ_1000)
48
#define CONFIG_MEM_ADD_WDTH 10
49
#define CONFIG_MEM_SIZE 64
51
#define CONFIG_EBIU_DDRCTL0_VAL 0x218A83FE
52
#define CONFIG_EBIU_DDRCTL1_VAL 0x20022222
53
#define CONFIG_EBIU_DDRCTL2_VAL 0x00000021
55
/* Default bank mapping:
56
* Async Bank 0 - 32MB Burst Flash
57
* Async Bank 1 - Ethernet
58
* Async Bank 2 - Nothing
59
* Async Bank 3 - Nothing
61
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
62
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
63
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
64
#define CONFIG_EBIU_FCTL_VAL (BCLK_4)
65
#define CONFIG_EBIU_MODE_VAL (B0MODE_FLASH)
67
#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
68
#define CONFIG_SYS_MALLOC_LEN (640 * 1024)
74
#define ADI_CMDS_NETWORK 1
75
#define CONFIG_NET_MULTI
76
#define CONFIG_SMC911X 1
77
#define CONFIG_SMC911X_BASE 0x24000000
78
#define CONFIG_SMC911X_16_BIT
79
#define CONFIG_HOSTNAME cm-bf548
80
/* Uncomment next line to use fixed MAC address */
81
/* #define CONFIG_ETHADDR 02:80:ad:24:31:91 */
87
#define CONFIG_FLASH_CFI_DRIVER
88
#define CONFIG_SYS_FLASH_BASE 0x20000000
89
#define CONFIG_SYS_FLASH_CFI
90
#define CONFIG_SYS_FLASH_PROTECTION
91
#define CONFIG_SYS_MAX_FLASH_BANKS 1
92
#define CONFIG_SYS_MAX_FLASH_SECT 259
96
* Env Storage Settings
98
#define CONFIG_ENV_IS_IN_FLASH 1
99
#define CONFIG_ENV_ADDR 0x20008000
100
#define CONFIG_ENV_OFFSET 0x8000
101
#define CONFIG_ENV_SIZE 0x8000
102
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
108
#define CONFIG_BFIN_TWI_I2C 1
109
#define CONFIG_HARD_I2C 1
110
#define CONFIG_SYS_I2C_SPEED 50000
111
#define CONFIG_SYS_I2C_SLAVE 0
117
#define CONFIG_BAUDRATE 115200
118
#define CONFIG_BOARD_EARLY_INIT_F
119
#define CONFIG_RTC_BFIN
120
#define CONFIG_UART_CONSOLE 1
121
#define CONFIG_BOOTCOMMAND "run flashboot"
122
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0"
124
#ifndef __ADSPBF542__
125
/* Don't waste time transferring a logo over the UART */
126
# if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
127
# define CONFIG_VIDEO
129
# define CONFIG_DEB_DMA_URGENT
132
/* Define if want to do post memory test */
135
#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
136
#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
141
* Pull in common ADI header for remaining command/environment setup
143
#include <configs/bfin_adi_common.h>