2
* Copyright (C) 2010 - ISEE 2007 SL
4
* Modified from mach-omap2/board-generic.c
6
* This program is free software; you can redistribute it and/or modify
7
* it under the terms of the GNU General Public License version 2 as
8
* published by the Free Software Foundation.
11
#include <linux/kernel.h>
12
#include <linux/init.h>
13
#include <linux/platform_device.h>
14
#include <linux/delay.h>
15
#include <linux/err.h>
16
#include <linux/clk.h>
18
#include <linux/gpio.h>
19
#include <linux/interrupt.h>
21
#include <linux/regulator/machine.h>
22
#include <linux/regulator/fixed.h>
23
#include <linux/i2c/twl.h>
24
#include <linux/mmc/host.h>
26
#include <asm/mach-types.h>
27
#include <asm/mach/arch.h>
29
#include <plat/board.h>
30
#include <plat/common.h>
31
#include <plat/gpmc.h>
33
#include <plat/onenand.h>
37
#include "sdram-numonyx-m65kxxxxam.h"
39
#define IGEP3_GPIO_LED0_GREEN 54
40
#define IGEP3_GPIO_LED0_RED 53
41
#define IGEP3_GPIO_LED1_RED 16
43
#define IGEP3_GPIO_WIFI_NPD 138
44
#define IGEP3_GPIO_WIFI_NRESET 139
45
#define IGEP3_GPIO_BT_NRESET 137
47
#define IGEP3_GPIO_USBH_NRESET 183
50
#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
51
defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
53
#define ONENAND_MAP 0x20000000
56
* x2 Flash built-in COMBO POP MEMORY
57
* Since the device is equipped with two DataRAMs, and two-plane NAND
58
* Flash memory array, these two component enables simultaneous program
59
* of 4KiB. Plane1 has only even blocks such as block0, block2, block4
60
* while Plane2 has only odd blocks such as block1, block3, block5.
61
* So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
64
static struct mtd_partition igep3_onenand_partitions[] = {
68
.size = 2 * (64*(2*2048))
72
.offset = MTDPART_OFS_APPEND,
73
.size = 6 * (64*(2*2048)),
76
.name = "Environment",
77
.offset = MTDPART_OFS_APPEND,
78
.size = 2 * (64*(2*2048)),
82
.offset = MTDPART_OFS_APPEND,
83
.size = 12 * (64*(2*2048)),
86
.name = "File System",
87
.offset = MTDPART_OFS_APPEND,
88
.size = MTDPART_SIZ_FULL,
92
static struct omap_onenand_platform_data igep3_onenand_pdata = {
93
.parts = igep3_onenand_partitions,
94
.nr_parts = ARRAY_SIZE(igep3_onenand_partitions),
95
.onenand_setup = NULL,
96
.dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
99
static struct platform_device igep3_onenand_device = {
100
.name = "omap2-onenand",
103
.platform_data = &igep3_onenand_pdata,
107
static void __init igep3_flash_init(void)
110
u8 onenandcs = GPMC_CS_NUM + 1;
112
for (cs = 0; cs < GPMC_CS_NUM; cs++) {
114
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
116
/* Check if NAND/oneNAND is configured */
117
if ((ret & 0xC00) == 0x800)
119
pr_err("IGEP3: Unsupported NAND found\n");
121
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
123
if ((ret & 0x3F) == (ONENAND_MAP >> 24))
129
if (onenandcs > GPMC_CS_NUM) {
130
pr_err("IGEP3: Unable to find configuration in GPMC\n");
134
igep3_onenand_pdata.cs = onenandcs;
136
if (platform_device_register(&igep3_onenand_device) < 0)
137
pr_err("IGEP3: Unable to register OneNAND device\n");
141
static void __init igep3_flash_init(void) {}
144
static struct regulator_consumer_supply igep3_vmmc1_supply =
145
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0");
147
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
148
static struct regulator_init_data igep3_vmmc1 = {
152
.valid_modes_mask = REGULATOR_MODE_NORMAL
153
| REGULATOR_MODE_STANDBY,
154
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
155
| REGULATOR_CHANGE_MODE
156
| REGULATOR_CHANGE_STATUS,
158
.num_consumer_supplies = 1,
159
.consumer_supplies = &igep3_vmmc1_supply,
162
static struct regulator_consumer_supply igep3_vio_supply =
163
REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1");
165
static struct regulator_init_data igep3_vio = {
170
.valid_modes_mask = REGULATOR_MODE_NORMAL
171
| REGULATOR_MODE_STANDBY,
172
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
173
| REGULATOR_CHANGE_MODE
174
| REGULATOR_CHANGE_STATUS,
176
.num_consumer_supplies = 1,
177
.consumer_supplies = &igep3_vio_supply,
180
static struct regulator_consumer_supply igep3_vmmc2_supply =
181
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1");
183
static struct regulator_init_data igep3_vmmc2 = {
185
.valid_modes_mask = REGULATOR_MODE_NORMAL,
188
.num_consumer_supplies = 1,
189
.consumer_supplies = &igep3_vmmc2_supply,
192
static struct fixed_voltage_config igep3_vwlan = {
193
.supply_name = "vwlan",
194
.microvolts = 3300000,
196
.enabled_at_boot = 1,
197
.init_data = &igep3_vmmc2,
200
static struct platform_device igep3_vwlan_device = {
201
.name = "reg-fixed-voltage",
204
.platform_data = &igep3_vwlan,
208
static struct omap2_hsmmc_info mmc[] = {
211
.caps = MMC_CAP_4_BIT_DATA,
215
#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
218
.caps = MMC_CAP_4_BIT_DATA,
226
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
227
#include <linux/leds.h>
229
static struct gpio_led igep3_gpio_leds[] = {
231
.name = "gpio-led:red:d0",
232
.gpio = IGEP3_GPIO_LED0_RED,
233
.default_trigger = "default-off"
236
.name = "gpio-led:green:d0",
237
.gpio = IGEP3_GPIO_LED0_GREEN,
238
.default_trigger = "default-off",
241
.name = "gpio-led:red:d1",
242
.gpio = IGEP3_GPIO_LED1_RED,
243
.default_trigger = "default-off",
246
.name = "gpio-led:green:d1",
247
.default_trigger = "heartbeat",
248
.gpio = -EINVAL, /* gets replaced */
252
static struct gpio_led_platform_data igep3_led_pdata = {
253
.leds = igep3_gpio_leds,
254
.num_leds = ARRAY_SIZE(igep3_gpio_leds),
257
static struct platform_device igep3_led_device = {
261
.platform_data = &igep3_led_pdata,
265
static void __init igep3_leds_init(void)
267
platform_device_register(&igep3_led_device);
271
static inline void igep3_leds_init(void)
273
if ((gpio_request(IGEP3_GPIO_LED0_RED, "gpio-led:red:d0") == 0) &&
274
(gpio_direction_output(IGEP3_GPIO_LED0_RED, 1) == 0)) {
275
gpio_export(IGEP3_GPIO_LED0_RED, 0);
276
gpio_set_value(IGEP3_GPIO_LED0_RED, 1);
278
pr_warning("IGEP3: Could not obtain gpio GPIO_LED0_RED\n");
280
if ((gpio_request(IGEP3_GPIO_LED0_GREEN, "gpio-led:green:d0") == 0) &&
281
(gpio_direction_output(IGEP3_GPIO_LED0_GREEN, 1) == 0)) {
282
gpio_export(IGEP3_GPIO_LED0_GREEN, 0);
283
gpio_set_value(IGEP3_GPIO_LED0_GREEN, 1);
285
pr_warning("IGEP3: Could not obtain gpio GPIO_LED0_GREEN\n");
287
if ((gpio_request(IGEP3_GPIO_LED1_RED, "gpio-led:red:d1") == 0) &&
288
(gpio_direction_output(IGEP3_GPIO_LED1_RED, 1) == 0)) {
289
gpio_export(IGEP3_GPIO_LED1_RED, 0);
290
gpio_set_value(IGEP3_GPIO_LED1_RED, 1);
292
pr_warning("IGEP3: Could not obtain gpio GPIO_LED1_RED\n");
296
static int igep3_twl4030_gpio_setup(struct device *dev,
297
unsigned gpio, unsigned ngpio)
299
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
300
mmc[0].gpio_cd = gpio + 0;
301
omap2_hsmmc_init(mmc);
303
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
304
#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
305
if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
306
&& (gpio_direction_output(gpio + TWL4030_GPIO_MAX + 1, 1) == 0)) {
307
gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
308
gpio_set_value(gpio + TWL4030_GPIO_MAX + 1, 0);
310
pr_warning("IGEP3: Could not obtain gpio GPIO_LED1_GREEN\n");
312
igep3_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
318
static struct twl4030_gpio_platform_data igep3_twl4030_gpio_pdata = {
319
.gpio_base = OMAP_MAX_GPIO_LINES,
320
.irq_base = TWL4030_GPIO_IRQ_BASE,
321
.irq_end = TWL4030_GPIO_IRQ_END,
323
.setup = igep3_twl4030_gpio_setup,
326
static struct twl4030_usb_data igep3_twl4030_usb_data = {
327
.usb_mode = T2_USB_MODE_ULPI,
330
static struct platform_device *igep3_devices[] __initdata = {
334
static void __init igep3_init_early(void)
336
omap2_init_common_infrastructure();
337
omap2_init_common_devices(m65kxxxxam_sdrc_params,
338
m65kxxxxam_sdrc_params);
341
static struct twl4030_platform_data igep3_twl4030_pdata = {
342
.irq_base = TWL4030_IRQ_BASE,
343
.irq_end = TWL4030_IRQ_END,
345
/* platform_data for children goes here */
346
.usb = &igep3_twl4030_usb_data,
347
.gpio = &igep3_twl4030_gpio_pdata,
348
.vmmc1 = &igep3_vmmc1,
352
static struct i2c_board_info __initdata igep3_i2c_boardinfo[] = {
354
I2C_BOARD_INFO("twl4030", 0x48),
355
.flags = I2C_CLIENT_WAKE,
356
.irq = INT_34XX_SYS_NIRQ,
357
.platform_data = &igep3_twl4030_pdata,
361
static int __init igep3_i2c_init(void)
363
omap_register_i2c_bus(1, 2600, igep3_i2c_boardinfo,
364
ARRAY_SIZE(igep3_i2c_boardinfo));
369
static struct omap_musb_board_data musb_board_data = {
370
.interface_type = MUSB_INTERFACE_ULPI,
375
#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
377
static void __init igep3_wifi_bt_init(void)
379
/* Configure MUX values for W-LAN + Bluetooth GPIO's */
380
omap_mux_init_gpio(IGEP3_GPIO_WIFI_NPD, OMAP_PIN_OUTPUT);
381
omap_mux_init_gpio(IGEP3_GPIO_WIFI_NRESET, OMAP_PIN_OUTPUT);
382
omap_mux_init_gpio(IGEP3_GPIO_BT_NRESET, OMAP_PIN_OUTPUT);
384
/* Set GPIO's for W-LAN + Bluetooth combo module */
385
if ((gpio_request(IGEP3_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
386
(gpio_direction_output(IGEP3_GPIO_WIFI_NPD, 1) == 0)) {
387
gpio_export(IGEP3_GPIO_WIFI_NPD, 0);
389
pr_warning("IGEP3: Could not obtain gpio GPIO_WIFI_NPD\n");
391
if ((gpio_request(IGEP3_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
392
(gpio_direction_output(IGEP3_GPIO_WIFI_NRESET, 1) == 0)) {
393
gpio_export(IGEP3_GPIO_WIFI_NRESET, 0);
394
gpio_set_value(IGEP3_GPIO_WIFI_NRESET, 0);
396
gpio_set_value(IGEP3_GPIO_WIFI_NRESET, 1);
398
pr_warning("IGEP3: Could not obtain gpio GPIO_WIFI_NRESET\n");
400
if ((gpio_request(IGEP3_GPIO_BT_NRESET, "GPIO_BT_NRESET") == 0) &&
401
(gpio_direction_output(IGEP3_GPIO_BT_NRESET, 1) == 0)) {
402
gpio_export(IGEP3_GPIO_BT_NRESET, 0);
404
pr_warning("IGEP3: Could not obtain gpio GPIO_BT_NRESET\n");
407
void __init igep3_wifi_bt_init(void) {}
410
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
411
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
412
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
413
.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
416
.reset_gpio_port[0] = -EINVAL,
417
.reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
418
.reset_gpio_port[2] = -EINVAL,
421
#ifdef CONFIG_OMAP_MUX
422
static struct omap_board_mux board_mux[] __initdata = {
423
OMAP3_MUX(I2C2_SDA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
424
{ .reg_offset = OMAP_MUX_TERMINATOR },
428
static void __init igep3_init(void)
430
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
432
/* Register I2C busses and drivers */
434
platform_add_devices(igep3_devices, ARRAY_SIZE(igep3_devices));
436
usb_musb_init(&musb_board_data);
437
usbhs_init(&usbhs_bdata);
443
* WLAN-BT combo module from MuRata wich has a Marvell WLAN
444
* (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
446
igep3_wifi_bt_init();
450
static const char *igep3_dt_compat[] __initdata = {
455
MACHINE_START(IGEP0030, "IGEP OMAP3 module")
456
.boot_params = 0x80000100,
457
.reserve = omap_reserve,
458
.map_io = omap3_map_io,
459
.init_early = igep3_init_early,
460
.init_irq = omap_init_irq,
461
.init_machine = igep3_init,
462
.timer = &omap_timer,
463
.dt_compat = &igep3_dt_compat,