7
#if defined(CONFIG_CMD_PCMCIA)
11
#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
17
#define PCMCIA_BOARD_MSG "R360MPI"
19
int pcmcia_hardware_enable(int slot)
21
volatile immap_t *immap;
22
volatile pcmconf8xx_t *pcmp;
23
volatile sysconf8xx_t *sysp;
26
debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
30
immap = (immap_t *)CONFIG_SYS_IMMR;
31
sysp = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
32
pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
35
* Configure SIUMCR to enable PCMCIA port B
36
* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
38
sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
40
/* clear interrupt state, and disable interrupts */
41
pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
42
pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
45
* Disable interrupts, DMA, and PCMCIA buffers
46
* (isolate the interface) and assert RESET signal
48
debug ("Disable PCMCIA buffers and assert RESET\n");
50
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
51
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
52
PCMCIA_PGCRX(_slot_) = reg;
56
* Configure Ports A, B & C pins for
57
* 5 Volts Enable and 3 Volts enable
59
immap->im_ioport.iop_pcpar &= ~(0x0400);
60
immap->im_ioport.iop_pcso &= ~(0x0400);/*
61
immap->im_ioport.iop_pcdir |= 0x0400;*/
63
immap->im_ioport.iop_papar &= ~(0x0200);/*
64
immap->im_ioport.iop_padir |= 0x0200;*/
66
immap->im_ioport.iop_pbpar &= ~(0xC000);
67
immap->im_ioport.iop_pbdir &= ~(0xC000);
69
/* remove all power */
71
immap->im_ioport.iop_pcdat |= 0x0400;
72
immap->im_ioport.iop_padat |= 0x0200;
75
* Make sure there is a card in the slot, then configure the interface.
78
debug ("[%d] %s: PIPR(%p)=0x%x\n",
79
__LINE__,__FUNCTION__,
80
&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
81
if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
82
printf (" No Card found\n");
89
mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
90
reg = pcmp->pcmc_pipr;
91
debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
93
(reg&PCMCIA_VS1(slot))?"n":"ff",
94
(reg&PCMCIA_VS2(slot))?"n":"ff");
95
if ((reg & mask) == mask) {
96
immap->im_ioport.iop_pcdat &= ~(0x4000);
97
puts (" 5.0V card found: ");
99
immap->im_ioport.iop_padat &= ~(0x0002);
100
puts (" 3.3V card found: ");
102
immap->im_ioport.iop_pcdir |= 0x0400;
103
immap->im_ioport.iop_padir |= 0x0200;
105
/* VCC switch error flag, PCMCIA slot INPACK_ pin */
106
cp->cp_pbdir &= ~(0x0020 | 0x0010);
107
cp->cp_pbpar &= ~(0x0020 | 0x0010);
110
debug ("Enable PCMCIA buffers and stop RESET\n");
111
reg = PCMCIA_PGCRX(_slot_);
112
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
113
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
114
PCMCIA_PGCRX(_slot_) = reg;
116
udelay(250000); /* some cards need >150 ms to come up :-( */
118
debug ("# hardware_enable done\n");
124
#if defined(CONFIG_CMD_PCMCIA)
125
int pcmcia_hardware_disable(int slot)
127
volatile immap_t *immap;
130
debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
132
immap = (immap_t *)CONFIG_SYS_IMMR;
134
/* remove all power */
135
immap->im_ioport.iop_pcdat |= 0x0400;
136
immap->im_ioport.iop_padat |= 0x0200;
138
/* Configure PCMCIA General Control Register */
139
debug ("Disable PCMCIA buffers and assert RESET\n");
141
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
142
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
143
PCMCIA_PGCRX(_slot_) = reg;
152
int pcmcia_voltage_set(int slot, int vcc, int vpp)
154
volatile immap_t *immap;
155
volatile pcmconf8xx_t *pcmp;
158
debug ("voltage_set: "
160
" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
161
'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
163
immap = (immap_t *)CONFIG_SYS_IMMR;
164
pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
166
* Disable PCMCIA buffers (isolate the interface)
167
* and assert RESET signal
169
debug ("Disable PCMCIA buffers and assert RESET\n");
170
reg = PCMCIA_PGCRX(_slot_);
171
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
172
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
173
PCMCIA_PGCRX(_slot_) = reg;
177
* Configure Ports A & C pins for
178
* 5 Volts Enable and 3 Volts enable,
181
debug ("PCMCIA power OFF\n");
182
immap->im_ioport.iop_pcpar &= ~(0x0400);
183
immap->im_ioport.iop_pcso &= ~(0x0400);/*
184
immap->im_ioport.iop_pcdir |= 0x0400;*/
186
immap->im_ioport.iop_papar &= ~(0x0200);/*
187
immap->im_ioport.iop_padir |= 0x0200;*/
189
immap->im_ioport.iop_pcdat |= 0x0400;
190
immap->im_ioport.iop_padat |= 0x0200;
195
case 33: reg |= 0x0200; break;
196
case 50: reg |= 0x0400; break;
200
/* Checking supported voltages */
202
debug ("PIPR: 0x%x --> %s\n",
204
(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
207
immap->im_ioport.iop_pcdat &= !reg;
209
immap->im_ioport.iop_padat &= !reg;
210
immap->im_ioport.iop_pcdir |= 0x0200;
211
immap->im_ioport.iop_padir |= 0x0400;
213
debug ("PCMCIA powered at %sV\n",
214
(reg&0x0400) ? "5.0" : "3.3");
216
debug ("PCMCIA powered down\n");
220
debug ("Enable PCMCIA buffers and stop RESET\n");
221
reg = PCMCIA_PGCRX(_slot_);
222
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
223
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
224
PCMCIA_PGCRX(_slot_) = reg;
227
debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
232
#endif /* CCONFIG_PCMCIA */