2
* (C) Copyright 2000-2004
3
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5
* SPDX-License-Identifier: GPL-2.0+
9
* The purpose of this code is to signal the operational status of a
10
* target which usually boots over the network; while running in
11
* PCBoot, a status LED is blinking. As soon as a valid BOOTP reply
12
* message has been received, the LED is turned off. The Linux
13
* kernel, once it is running, will start blinking the LED again,
14
* with another frequency.
17
#ifndef _STATUS_LED_H_
18
#define _STATUS_LED_H_
20
#ifdef CONFIG_STATUS_LED
22
#define STATUS_LED_OFF 0
23
#define STATUS_LED_BLINKING 1
24
#define STATUS_LED_ON 2
26
void status_led_tick (unsigned long timestamp);
27
void status_led_set (int led, int state);
29
/***** TQM8xxL ********************************************************/
30
#if defined(CONFIG_TQM8xxL)
31
# define STATUS_LED_PAR im_cpm.cp_pbpar
32
# define STATUS_LED_DIR im_cpm.cp_pbdir
33
# define STATUS_LED_ODR im_cpm.cp_pbodr
34
# define STATUS_LED_DAT im_cpm.cp_pbdat
36
# define STATUS_LED_BIT 0x00000001
37
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
38
# define STATUS_LED_STATE STATUS_LED_BLINKING
40
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
42
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
44
/***** MVS v1 **********************************************************/
45
#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2)
46
# define STATUS_LED_PAR im_ioport.iop_pdpar
47
# define STATUS_LED_DIR im_ioport.iop_pddir
48
# undef STATUS_LED_ODR
49
# define STATUS_LED_DAT im_ioport.iop_pddat
51
# define STATUS_LED_BIT 0x00000001
52
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
53
# define STATUS_LED_STATE STATUS_LED_BLINKING
55
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
57
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
59
/***** GEN860T *********************************************************/
60
#elif defined(CONFIG_GEN860T)
62
# define STATUS_LED_PAR im_ioport.iop_papar
63
# define STATUS_LED_DIR im_ioport.iop_padir
64
# define STATUS_LED_ODR im_ioport.iop_paodr
65
# define STATUS_LED_DAT im_ioport.iop_padat
67
# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */
68
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
69
# define STATUS_LED_STATE STATUS_LED_OFF
70
# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */
71
# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8)
72
# define STATUS_LED_STATE1 STATUS_LED_BLINKING
73
# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */
74
# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4)
75
# define STATUS_LED_STATE2 STATUS_LED_OFF
76
# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */
77
# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4)
78
# define STATUS_LED_STATE3 STATUS_LED_OFF
80
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
81
# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */
83
/***** IVMS8 **********************************************************/
84
#elif defined(CONFIG_IVMS8)
86
# define STATUS_LED_PAR im_cpm.cp_pbpar
87
# define STATUS_LED_DIR im_cpm.cp_pbdir
88
# define STATUS_LED_ODR im_cpm.cp_pbodr
89
# define STATUS_LED_DAT im_cpm.cp_pbdat
91
# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */
92
# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ)
93
# define STATUS_LED_STATE STATUS_LED_OFF
94
# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */
95
# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ)
96
# define STATUS_LED_STATE1 STATUS_LED_OFF
97
/* IDE LED usable for other purposes, too */
98
# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */
99
# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ)
100
# define STATUS_LED_STATE2 STATUS_LED_OFF
102
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
104
# define STATUS_ILOCK_SWITCH 0x00800000 /* ILOCK switch in IRQ4 */
106
# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */
108
# define STATUS_LED_YELLOW 0
109
# define STATUS_LED_GREEN 1
110
# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
112
/***** IVML24 *********************************************************/
113
#elif defined(CONFIG_IVML24)
115
# define STATUS_LED_PAR im_cpm.cp_pbpar
116
# define STATUS_LED_DIR im_cpm.cp_pbdir
117
# define STATUS_LED_ODR im_cpm.cp_pbodr
118
# define STATUS_LED_DAT im_cpm.cp_pbdat
120
# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */
121
# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ)
122
# define STATUS_LED_STATE STATUS_LED_OFF
123
# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */
124
# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ)
125
# define STATUS_LED_STATE1 STATUS_LED_OFF
126
/* IDE LED usable for other purposes, too */
127
# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */
128
# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ)
129
# define STATUS_LED_STATE2 STATUS_LED_OFF
131
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
133
# define STATUS_ILOCK_SWITCH 0x00004000 /* ILOCK is on PB.17 */
135
# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */
137
# define STATUS_LED_YELLOW 0
138
# define STATUS_LED_GREEN 1
139
# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */
141
/***** ICU862 ********************************************************/
142
#elif defined(CONFIG_ICU862)
144
# define STATUS_LED_PAR im_ioport.iop_papar
145
# define STATUS_LED_DIR im_ioport.iop_padir
146
# define STATUS_LED_ODR im_ioport.iop_paodr
147
# define STATUS_LED_DAT im_ioport.iop_padat
149
# define STATUS_LED_BIT 0x4000 /* LED 0 is on PA.1 */
150
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
151
# define STATUS_LED_STATE STATUS_LED_BLINKING
152
# define STATUS_LED_BIT1 0x1000 /* LED 1 is on PA.3 */
153
# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
154
# define STATUS_LED_STATE1 STATUS_LED_OFF
156
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
158
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
160
/***** Someone else defines these *************************************/
161
#elif defined(STATUS_LED_PAR)
164
* ADVICE: Define in your board configuration file rather than
165
* filling this file up with lots of custom board stuff.
168
/***** NetVia ********************************************************/
169
#elif defined(CONFIG_NETVIA)
171
#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
173
#define STATUS_LED_PAR im_ioport.iop_pdpar
174
#define STATUS_LED_DIR im_ioport.iop_pddir
175
#undef STATUS_LED_ODR
176
#define STATUS_LED_DAT im_ioport.iop_pddat
178
# define STATUS_LED_BIT 0x0080 /* PD.8 */
179
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
180
# define STATUS_LED_STATE STATUS_LED_BLINKING
182
# define STATUS_LED_BIT1 0x0040 /* PD.9 */
183
# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
184
# define STATUS_LED_STATE1 STATUS_LED_OFF
186
# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
187
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
191
/***** CMI ********************************************************/
192
#elif defined(CONFIG_CMI)
193
# define STATUS_LED_DIR im_mios.mios_mpiosm32ddr
194
# define STATUS_LED_DAT im_mios.mios_mpiosm32dr
196
# define STATUS_LED_BIT 0x2000 /* Select one of the 16 possible*/
198
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* Blinking periode is 500 ms */
199
# define STATUS_LED_STATE STATUS_LED_BLINKING
201
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 0 */
202
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
204
/***** KUP4K, KUP4X ****************************************************/
205
#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
207
# define STATUS_LED_PAR im_ioport.iop_papar
208
# define STATUS_LED_DIR im_ioport.iop_padir
209
# define STATUS_LED_ODR im_ioport.iop_paodr
210
# define STATUS_LED_DAT im_ioport.iop_padat
212
# define STATUS_LED_BIT 0x00000300 /* green + red PA[8]=yellow, PA[7]=red, PA[6]=green */
213
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
214
# define STATUS_LED_STATE STATUS_LED_BLINKING
216
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
218
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
220
#elif defined(CONFIG_SVM_SC8xx)
221
# define STATUS_LED_PAR im_cpm.cp_pbpar
222
# define STATUS_LED_DIR im_cpm.cp_pbdir
223
# define STATUS_LED_ODR im_cpm.cp_pbodr
224
# define STATUS_LED_DAT im_cpm.cp_pbdat
226
# define STATUS_LED_BIT 0x00000001
227
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
228
# define STATUS_LED_STATE STATUS_LED_BLINKING
230
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
232
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
234
/***** RBC823 ********************************************************/
235
#elif defined(CONFIG_RBC823)
237
# define STATUS_LED_PAR im_ioport.iop_pcpar
238
# define STATUS_LED_DIR im_ioport.iop_pcdir
239
# undef STATUS_LED_ODR
240
# define STATUS_LED_DAT im_ioport.iop_pcdat
242
# define STATUS_LED_BIT 0x0002 /* LED 0 is on PC.14 */
243
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
244
# define STATUS_LED_STATE STATUS_LED_BLINKING
245
# define STATUS_LED_BIT1 0x0004 /* LED 1 is on PC.13 */
246
# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
247
# define STATUS_LED_STATE1 STATUS_LED_OFF
249
# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
251
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
253
/***** NetPhone ********************************************************/
254
#elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
255
/* XXX empty just to avoid the error */
256
/***** STx XTc ********************************************************/
257
#elif defined(CONFIG_STXXTC)
258
/* XXX empty just to avoid the error */
259
/************************************************************************/
260
#elif defined(CONFIG_V38B)
262
# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */
263
# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
264
# define STATUS_LED_STATE STATUS_LED_BLINKING
266
# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
267
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
269
#elif defined(CONFIG_MOTIONPRO)
271
#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE)
272
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 10)
273
#define STATUS_LED_STATE STATUS_LED_BLINKING
275
#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE)
276
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 10)
277
#define STATUS_LED_STATE1 STATUS_LED_OFF
279
#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
281
#elif defined(CONFIG_BOARD_SPECIFIC_LED)
282
/* led_id_t is unsigned long mask */
283
typedef unsigned long led_id_t;
285
extern void __led_toggle (led_id_t mask);
286
extern void __led_init (led_id_t mask, int state);
287
extern void __led_set (led_id_t mask, int state);
289
# error Status LED configuration missing
291
/************************************************************************/
293
#ifndef CONFIG_BOARD_SPECIFIC_LED
294
# include <asm/status_led.h>
301
extern void coloured_LED_init (void);
302
extern void red_led_on(void);
303
extern void red_led_off(void);
304
extern void green_led_on(void);
305
extern void green_led_off(void);
306
extern void yellow_led_on(void);
307
extern void yellow_led_off(void);
308
extern void blue_led_on(void);
309
extern void blue_led_off(void);
314
.extern yellow_led_on
315
.extern yellow_led_off
317
.extern green_led_off
322
#endif /* CONFIG_STATUS_LED */
324
#endif /* _STATUS_LED_H_ */