4
* Linus Walleij <linus.walleij@linaro.org>
5
* Common ARM Integrator configuration settings
7
* SPDX-License-Identifier: GPL-2.0+
10
#define CONFIG_INTEGRATOR
12
#define CONFIG_SYS_TEXT_BASE 0x01000000
13
#define CONFIG_SYS_MEMTEST_START 0x100000
14
#define CONFIG_SYS_MEMTEST_END 0x10000000
15
#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */
16
#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
17
#define CONFIG_SYS_LONGHELP
18
#define CONFIG_SYS_HUSH_PARSER
19
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/
20
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
21
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
22
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/
23
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */
25
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
26
#define CONFIG_SETUP_MEMORY_TAGS
27
#define CONFIG_OF_LIBFDT /* enable passing a Device Tree */
28
#define CONFIG_MISC_INIT_R /* call misc_init_r during start up */
31
* There are various dependencies on the core module (CM) fitted
32
* Users should refer to their CM user guide
34
#include "armcoremodule.h"
37
* Initialize and remap the core module, use SPD to detect memory size
38
* If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
39
* the core module has a CM_INIT register
40
* then the U-Boot initialisation code will
41
* e.g. ARM Boot Monitor or pre-loader is repeated once
42
* (to re-initialise any existing CM_INIT settings to safe values).
44
* This is usually not the desired behaviour since the platform
45
* will either reboot into the ARM monitor (or pre-loader)
46
* or continuously cycle thru it without U-Boot running,
47
* depending upon the setting of Integrator/CP switch S2-4.
49
* However it may be needed if Integrator/CP switch S2-1
50
* is set OFF to boot direct into U-Boot.
51
* In that case comment out the line below.
53
#define CONFIG_CM_INIT
54
#define CONFIG_CM_REMAP
55
#define CONFIG_CM_SPD_DETECT
58
* The ARM boot monitor initializes the board.
59
* However, the default U-Boot code also performs the initialization.
60
* If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT
61
* - see documentation supplied with board for details of how to choose the
62
* image to run at reset/power up
63
* e.g. whether the ARM Boot Monitor runs before U-Boot
65
/* #define CONFIG_SKIP_LOWLEVEL_INIT */
68
* The ARM boot monitor does not relocate U-Boot.
69
* However, the default U-Boot code performs the relocation check,
70
* and may relocate the code if the memory map is changed.
71
* If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT
73
/* #define SKIP_CONFIG_RELOCATE_UBOOT */
79
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
80
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
81
#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
82
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
83
#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE
84
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
85
CONFIG_SYS_INIT_RAM_SIZE - \
86
GENERATED_GBL_DATA_SIZE)
87
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET