2
* smc911x_eeprom.c - EEPROM interface to SMC911x parts.
3
* Only tested on SMSC9118 though ...
5
* Copyright 2004-2009 Analog Devices Inc.
7
* Licensed under the GPL-2 or later.
9
* Based on smc91111_eeprom.c which:
10
* Heavily borrowed from the following peoples GPL'ed software:
11
* - Wolfgang Denk, DENX Software Engineering, wd@denx.de
13
* - Ladislav Michl ladis@linux-mips.org
14
* A rejected patch on the U-Boot mailing list
19
#include <linux/ctype.h>
20
#include "../drivers/net/smc911x.h"
23
* smsc_ctrlc - detect press of CTRL+C (common ctrlc() isnt exported!?)
25
static int smsc_ctrlc(void)
27
return (tstc() && getc() == 0x03);
31
* usage - dump usage information
33
static void usage(void)
36
"MAC/EEPROM Commands:\n"
37
" P : Print the MAC addresses\n"
38
" D : Dump the EEPROM contents\n"
39
" M : Dump the MAC contents\n"
40
" C : Copy the MAC address from the EEPROM to the MAC\n"
41
" W : Write a register in the EEPROM or in the MAC\n"
44
"Some commands take arguments:\n"
45
" W <E|M> <register> <value>\n"
51
* dump_regs - dump the MAC registers
53
* Registers 0x00 - 0x50 are FIFOs. The 0x50+ are the control registers
54
* and they're all 32bits long. 0xB8+ are reserved, so don't bother.
56
static void dump_regs(struct eth_device *dev)
59
for (i = 0x50; i < 0xB8; i += sizeof(u32))
60
printf("%02x: 0x%08x %c", i,
61
smc911x_reg_read(dev, i),
62
(j++ % 2 ? '\n' : ' '));
66
* do_eeprom_cmd - handle eeprom communication
68
static int do_eeprom_cmd(struct eth_device *dev, int cmd, u8 reg)
70
if (smc911x_reg_read(dev, E2P_CMD) & E2P_CMD_EPC_BUSY) {
71
printf("eeprom_cmd: busy at start (E2P_CMD = 0x%08x)\n",
72
smc911x_reg_read(dev, E2P_CMD));
76
smc911x_reg_write(dev, E2P_CMD, E2P_CMD_EPC_BUSY | cmd | reg);
78
while (smc911x_reg_read(dev, E2P_CMD) & E2P_CMD_EPC_BUSY)
80
printf("eeprom_cmd: timeout (E2P_CMD = 0x%08x)\n",
81
smc911x_reg_read(dev, E2P_CMD));
89
* read_eeprom_reg - read specified register in EEPROM
91
static u8 read_eeprom_reg(struct eth_device *dev, u8 reg)
93
int ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_READ, reg);
94
return (ret ? : smc911x_reg_read(dev, E2P_DATA));
98
* write_eeprom_reg - write specified value into specified register in EEPROM
100
static int write_eeprom_reg(struct eth_device *dev, u8 value, u8 reg)
104
/* enable erasing/writing */
105
ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_EWEN, reg);
109
/* erase the eeprom reg */
110
ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_ERASE, reg);
114
/* write the eeprom reg */
115
smc911x_reg_write(dev, E2P_DATA, value);
116
ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_WRITE, reg);
120
/* disable erasing/writing */
121
ret = do_eeprom_cmd(dev, E2P_CMD_EPC_CMD_EWDS, reg);
128
* skip_space - find first non-whitespace in given pointer
130
static char *skip_space(char *buf)
132
while (isblank(buf[0]))
138
* write_stuff - handle writing of MAC registers / eeprom
140
static void write_stuff(struct eth_device *dev, char *line)
147
/* Skip over the "W " part of the command */
148
line = skip_space(line + 1);
150
/* Figure out destination */
158
printf("ERROR: Invalid write usage\n");
163
/* Get the register to write */
164
line = skip_space(line + 1);
165
reg = simple_strtoul(line, &endp, 16);
169
/* Get the value to write */
170
line = skip_space(endp);
171
value = simple_strtoul(line, &endp, 16);
175
/* Check for trailing cruft */
176
line = skip_space(endp);
180
/* Finally, execute the command */
182
printf("Writing EEPROM register %02x with %02x\n", reg, value);
183
write_eeprom_reg(dev, value, reg);
185
printf("Writing MAC register %02x with %08x\n", reg, value);
186
smc911x_reg_write(dev, reg, value);
191
* copy_from_eeprom - copy MAC address in eeprom to address registers
193
static void copy_from_eeprom(struct eth_device *dev)
196
read_eeprom_reg(dev, 0x01) |
197
read_eeprom_reg(dev, 0x02) << 8 |
198
read_eeprom_reg(dev, 0x03) << 16 |
199
read_eeprom_reg(dev, 0x04) << 24;
201
read_eeprom_reg(dev, 0x05) |
202
read_eeprom_reg(dev, 0x06) << 8;
203
smc911x_set_mac_csr(dev, ADDRL, addrl);
204
smc911x_set_mac_csr(dev, ADDRH, addrh);
205
puts("EEPROM contents copied to MAC\n");
209
* print_macaddr - print MAC address registers and MAC address in eeprom
211
static void print_macaddr(struct eth_device *dev)
213
puts("Current MAC Address in MAC: ");
214
ulong addrl = smc911x_get_mac_csr(dev, ADDRL);
215
ulong addrh = smc911x_get_mac_csr(dev, ADDRH);
216
printf("%02x:%02x:%02x:%02x:%02x:%02x\n",
217
(u8)(addrl), (u8)(addrl >> 8), (u8)(addrl >> 16),
218
(u8)(addrl >> 24), (u8)(addrh), (u8)(addrh >> 8));
220
puts("Current MAC Address in EEPROM: ");
222
for (i = 1; i < 6; ++i)
223
printf("%02x:", read_eeprom_reg(dev, i));
224
printf("%02x\n", read_eeprom_reg(dev, i));
228
* dump_eeprom - dump the whole content of the EEPROM
230
static void dump_eeprom(struct eth_device *dev)
234
for (i = 0; i < 7; ++i)
235
printf("%02x: 0x%02x\n", i, read_eeprom_reg(dev, i));
239
* smc911x_init - get the MAC/EEPROM up and ready for use
241
static int smc911x_init(struct eth_device *dev)
243
/* See if there is anything there */
244
if (smc911x_detect_chip(dev))
249
/* Make sure we set EEDIO/EECLK to the EEPROM */
250
if (smc911x_reg_read(dev, GPIO_CFG) & GPIO_CFG_EEPR_EN) {
251
while (smc911x_reg_read(dev, E2P_CMD) & E2P_CMD_EPC_BUSY)
253
printf("init: timeout (E2P_CMD = 0x%08x)\n",
254
smc911x_reg_read(dev, E2P_CMD));
257
smc911x_reg_write(dev, GPIO_CFG,
258
smc911x_reg_read(dev, GPIO_CFG) & ~GPIO_CFG_EEPR_EN);
265
* getline - consume a line of input and handle some escape sequences
267
static char *getline(void)
269
static char buffer[100];
280
/* Convert to uppercase */
281
if (c >= 'a' && c <= 'z')
285
case '\r': /* Enter/Return key */
290
case 0x03: /* ^C - break */
294
case 0x08: /* ^H - backspace */
295
case 0x7F: /* DEL - backspace */
303
/* Ignore control characters */
306
/* Queue up all other characters */
315
* smc911x_eeprom - our application's main() function
317
int smc911x_eeprom(int argc, char * const argv[])
319
/* Avoid initializing on stack as gcc likes to call memset() */
320
struct eth_device dev;
321
dev.iobase = CONFIG_SMC911X_BASE;
323
/* Print the ABI version */
325
if (XF_VERSION != get_version()) {
326
printf("Expects ABI version %d\n", XF_VERSION);
327
printf("Actual U-Boot ABI version %lu\n", get_version());
328
printf("Can't run\n\n");
332
/* Initialize the MAC/EEPROM somewhat */
334
if (smc911x_init(&dev))
337
/* Dump helpful usage information */
345
/* Send the prompt and wait for a line */
353
/* Eat leading space */
354
line = skip_space(line);
356
/* Empty line, try again */
360
/* Only accept 1 letter commands */
361
if (line[0] && line[1] && !isblank(line[1]))
364
/* Now parse the command */
366
case 'W': write_stuff(&dev, line); break;
367
case 'D': dump_eeprom(&dev); break;
368
case 'M': dump_regs(&dev); break;
369
case 'C': copy_from_eeprom(&dev); break;
370
case 'P': print_macaddr(&dev); break;
372
default: puts("ERROR: Unknown command!\n\n");
374
case 'H': usage(); break;