2
* arch/arm/mach-u300/spi.c
4
* Copyright (C) 2009 ST-Ericsson AB
5
* License terms: GNU General Public License (GPL) version 2
7
* Author: Linus Walleij <linus.walleij@stericsson.com>
9
#include <linux/device.h>
10
#include <linux/amba/bus.h>
11
#include <linux/spi/spi.h>
12
#include <linux/amba/pl022.h>
13
#include <linux/err.h>
14
#include <mach/coh901318.h>
15
#include <mach/dma_channels.h>
18
* The following is for the actual devices on the SSP/SPI bus
20
#ifdef CONFIG_MACH_U300_SPIDUMMY
21
static void select_dummy_chip(u32 chipselect)
23
pr_debug("CORE: %s called with CS=0x%x (%s)\n",
26
chipselect ? "unselect chip" : "select chip");
28
* Here you would write the chip select value to the GPIO pins if
29
* this was a real chip (but this is a loopback dummy).
33
struct pl022_config_chip dummy_chip_info = {
34
/* available POLLING_TRANSFER, INTERRUPT_TRANSFER, DMA_TRANSFER */
35
.com_mode = DMA_TRANSFER,
36
.iface = SSP_INTERFACE_MOTOROLA_SPI,
37
/* We can only act as master but SSP_SLAVE is possible in theory */
38
.hierarchy = SSP_MASTER,
39
/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
40
.slave_tx_disable = 0,
41
.rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
42
.tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
43
.ctrl_len = SSP_BITS_12,
44
.wait_state = SSP_MWIRE_WAIT_ZERO,
45
.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
47
* This is where you insert a call to a function to enable CS
48
* (usually GPIO) for a certain chip.
50
.cs_control = select_dummy_chip,
54
static struct spi_board_info u300_spi_devices[] = {
55
#ifdef CONFIG_MACH_U300_SPIDUMMY
57
/* A dummy chip used for loopback tests */
58
.modalias = "spi-dummy",
59
/* Really dummy, pass in additional chip config here */
60
.platform_data = NULL,
61
/* This defines how the controller shall handle the device */
62
.controller_data = &dummy_chip_info,
63
/* .irq - no external IRQ routed from this device */
64
.max_speed_hz = 1000000,
65
.bus_num = 0, /* Only one bus on this chip */
67
/* Means SPI_CS_HIGH, change if e.g low CS */
68
.mode = SPI_MODE_1 | SPI_LOOP,
73
static struct pl022_ssp_controller ssp_platform_data = {
74
/* If you have several SPI buses this varies, we have only bus 0 */
77
* On the APP CPU GPIO 4, 5 and 6 are connected as generic
78
* chip selects for SPI. (Same on U330, U335 and U365.)
79
* TODO: make sure the GPIO driver can select these properly
80
* and do padmuxing accordingly too.
83
#ifdef CONFIG_COH901318
85
.dma_filter = coh901318_filter_id,
86
.dma_rx_param = (void *) U300_DMA_SPI_RX,
87
.dma_tx_param = (void *) U300_DMA_SPI_TX,
94
void __init u300_spi_init(struct amba_device *adev)
96
adev->dev.platform_data = &ssp_platform_data;
99
void __init u300_spi_register_board_devices(void)
101
/* Register any SPI devices */
102
spi_register_board_info(u300_spi_devices, ARRAY_SIZE(u300_spi_devices));