2
* Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
3
* Copyright (C) 2010 Jason Wang <jason77.wang@gmail.com>
5
* The code contained herein is licensed under the GNU General Public
6
* License. You may obtain a copy of the GNU General Public License
7
* Version 2 or later at the following locations:
9
* http://www.opensource.org/licenses/gpl-license.html
10
* http://www.gnu.org/copyleft/gpl.html
13
#include <linux/interrupt.h>
14
#include <linux/irq.h>
16
#include <linux/platform_device.h>
17
#include <linux/gpio.h>
18
#include <linux/smsc911x.h>
20
#include <mach/hardware.h>
22
/* LAN9217 ethernet base address */
23
#define LAN9217_BASE_ADDR(n) (n + 0x0)
25
#define UARTA_BASE_ADDR(n) (n + 0x8000)
26
#define UARTB_BASE_ADDR(n) (n + 0x10000)
28
#define BOARD_IO_ADDR(n) (n + 0x20000)
30
#define LED_SWITCH_REG 0x00
32
#define SWITCH_BUTTONS_REG 0x08
33
/* status, interrupt */
34
#define INTR_STATUS_REG 0x10
35
#define INTR_MASK_REG 0x38
36
#define INTR_RESET_REG 0x20
37
/* magic word for debug CPLD */
38
#define MAGIC_NUMBER1_REG 0x40
39
#define MAGIC_NUMBER2_REG 0x48
40
/* CPLD code version */
41
#define CPLD_CODE_VER_REG 0x50
42
/* magic word for debug CPLD */
43
#define MAGIC_NUMBER3_REG 0x58
44
/* module reset register*/
45
#define MODULE_RESET_REG 0x60
46
/* CPU ID and Personality ID */
47
#define MCU_BOARD_ID_REG 0x68
49
#define MXC_IRQ_TO_EXPIO(irq) ((irq) - MXC_BOARD_IRQ_START)
50
#define MXC_IRQ_TO_GPIO(irq) ((irq) - MXC_INTERNAL_IRQS)
52
#define MXC_EXP_IO_BASE (MXC_BOARD_IRQ_START)
53
#define MXC_MAX_EXP_IO_LINES 16
55
/* interrupts like external uart , external ethernet etc*/
56
#define EXPIO_INT_ENET (MXC_BOARD_IRQ_START + 0)
57
#define EXPIO_INT_XUART_A (MXC_BOARD_IRQ_START + 1)
58
#define EXPIO_INT_XUART_B (MXC_BOARD_IRQ_START + 2)
59
#define EXPIO_INT_BUTTON_A (MXC_BOARD_IRQ_START + 3)
60
#define EXPIO_INT_BUTTON_B (MXC_BOARD_IRQ_START + 4)
62
static void __iomem *brd_io;
64
static struct resource smsc911x_resources[] = {
66
.flags = IORESOURCE_MEM,
68
.start = EXPIO_INT_ENET,
69
.end = EXPIO_INT_ENET,
70
.flags = IORESOURCE_IRQ,
74
static struct smsc911x_platform_config smsc911x_config = {
75
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
76
.flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
79
static struct platform_device smsc_lan9217_device = {
83
.platform_data = &smsc911x_config,
85
.num_resources = ARRAY_SIZE(smsc911x_resources),
86
.resource = smsc911x_resources,
89
static void mxc_expio_irq_handler(u32 irq, struct irq_desc *desc)
95
/* irq = gpio irq number */
96
desc->irq_data.chip->irq_mask(&desc->irq_data);
98
imr_val = __raw_readw(brd_io + INTR_MASK_REG);
99
int_valid = __raw_readw(brd_io + INTR_STATUS_REG) & ~imr_val;
101
expio_irq = MXC_BOARD_IRQ_START;
102
for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
103
if ((int_valid & 1) == 0)
105
generic_handle_irq(expio_irq);
108
desc->irq_data.chip->irq_ack(&desc->irq_data);
109
desc->irq_data.chip->irq_unmask(&desc->irq_data);
113
* Disable an expio pin's interrupt by setting the bit in the imr.
114
* Irq is an expio virtual irq number
116
static void expio_mask_irq(struct irq_data *d)
119
u32 expio = MXC_IRQ_TO_EXPIO(d->irq);
121
reg = __raw_readw(brd_io + INTR_MASK_REG);
123
__raw_writew(reg, brd_io + INTR_MASK_REG);
126
static void expio_ack_irq(struct irq_data *d)
128
u32 expio = MXC_IRQ_TO_EXPIO(d->irq);
130
__raw_writew(1 << expio, brd_io + INTR_RESET_REG);
131
__raw_writew(0, brd_io + INTR_RESET_REG);
135
static void expio_unmask_irq(struct irq_data *d)
138
u32 expio = MXC_IRQ_TO_EXPIO(d->irq);
140
reg = __raw_readw(brd_io + INTR_MASK_REG);
141
reg &= ~(1 << expio);
142
__raw_writew(reg, brd_io + INTR_MASK_REG);
145
static struct irq_chip expio_irq_chip = {
146
.irq_ack = expio_ack_irq,
147
.irq_mask = expio_mask_irq,
148
.irq_unmask = expio_unmask_irq,
151
int __init mxc_expio_init(u32 base, u32 p_irq)
155
brd_io = ioremap(BOARD_IO_ADDR(base), SZ_4K);
159
if ((__raw_readw(brd_io + MAGIC_NUMBER1_REG) != 0xAAAA) ||
160
(__raw_readw(brd_io + MAGIC_NUMBER2_REG) != 0x5555) ||
161
(__raw_readw(brd_io + MAGIC_NUMBER3_REG) != 0xCAFE)) {
162
pr_info("3-Stack Debug board not detected\n");
168
pr_info("3-Stack Debug board detected, rev = 0x%04X\n",
169
readw(brd_io + CPLD_CODE_VER_REG));
172
* Configure INT line as GPIO input
174
gpio_request(MXC_IRQ_TO_GPIO(p_irq), "expio_pirq");
175
gpio_direction_input(MXC_IRQ_TO_GPIO(p_irq));
177
/* disable the interrupt and clear the status */
178
__raw_writew(0, brd_io + INTR_MASK_REG);
179
__raw_writew(0xFFFF, brd_io + INTR_RESET_REG);
180
__raw_writew(0, brd_io + INTR_RESET_REG);
181
__raw_writew(0x1F, brd_io + INTR_MASK_REG);
182
for (i = MXC_EXP_IO_BASE;
183
i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES); i++) {
184
irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
185
set_irq_flags(i, IRQF_VALID);
187
irq_set_irq_type(p_irq, IRQF_TRIGGER_LOW);
188
irq_set_chained_handler(p_irq, mxc_expio_irq_handler);
190
/* Register Lan device on the debugboard */
191
smsc911x_resources[0].start = LAN9217_BASE_ADDR(base);
192
smsc911x_resources[0].end = LAN9217_BASE_ADDR(base) + 0x100 - 1;
193
platform_device_register(&smsc_lan9217_device);