2
fit2.c (c) 1998 Grant R. Guenther <grant@torque.net>
3
Under the terms of the GNU General Public License.
5
fit2.c is a low-level protocol driver for the older version
6
of the Fidelity International Technology parallel port adapter.
7
This adapter is used in their TransDisk 2000 and older TransDisk
8
3000 portable hard-drives. As far as I can tell, this device
9
supports 4-bit mode _only_.
11
Newer models of the FIT products use an enhanced protocol.
12
The "fit3" protocol module should support current drives.
16
#define FIT2_VERSION "1.0"
18
#include <linux/module.h>
19
#include <linux/init.h>
20
#include <linux/delay.h>
21
#include <linux/kernel.h>
22
#include <linux/types.h>
23
#include <linux/wait.h>
28
#define j44(a,b) (((a>>4)&0x0f)|(b&0xf0))
30
/* cont = 0 - access the IDE register file
31
cont = 1 - access the IDE command set
33
NB: The FIT adapter does not appear to use the control registers.
34
So, we map ALT_STATUS to STATUS and NO-OP writes to the device
35
control register - this means that IDE reset will not work on these
40
static void fit2_write_regr( PIA *pi, int cont, int regr, int val)
42
{ if (cont == 1) return;
43
w2(0xc); w0(regr); w2(4); w0(val); w2(5); w0(0); w2(4);
46
static int fit2_read_regr( PIA *pi, int cont, int regr )
51
if (regr != 6) return 0xff;
53
} else r = regr + 0x10;
55
w2(0xc); w0(r); w2(4); w2(5);
64
static void fit2_read_block( PIA *pi, char * buf, int count )
70
for (k=0;k<count/4;k++) {
73
w0(0); a = r1(); w0(1); b = r1();
74
w0(3); c = r1(); w0(2); d = r1();
75
buf[4*k+0] = j44(a,b);
76
buf[4*k+1] = j44(d,c);
79
a = r1(); w0(3); b = r1();
80
w0(1); c = r1(); w0(0); d = r1();
81
buf[4*k+2] = j44(d,c);
82
buf[4*k+3] = j44(a,b);
90
static void fit2_write_block( PIA *pi, char * buf, int count )
96
for (k=0;k<count/2;k++) {
98
w2(5); w0(buf[2*k+1]);
103
static void fit2_connect ( PIA *pi )
105
{ pi->saved_r0 = r0();
110
static void fit2_disconnect ( PIA *pi )
116
static void fit2_log_adapter( PIA *pi, char * scratch, int verbose )
118
{ printk("%s: fit2 %s, FIT 2000 adapter at 0x%x, delay %d\n",
119
pi->device,FIT2_VERSION,pi->port,pi->delay);
123
static struct pi_protocol fit2 = {
124
.owner = THIS_MODULE,
130
.write_regr = fit2_write_regr,
131
.read_regr = fit2_read_regr,
132
.write_block = fit2_write_block,
133
.read_block = fit2_read_block,
134
.connect = fit2_connect,
135
.disconnect = fit2_disconnect,
136
.log_adapter = fit2_log_adapter,
139
static int __init fit2_init(void)
141
return paride_register(&fit2);
144
static void __exit fit2_exit(void)
146
paride_unregister(&fit2);
149
MODULE_LICENSE("GPL");
150
module_init(fit2_init)
151
module_exit(fit2_exit)