2
* Copyright (C) 2002 Intersil Americas Inc.
3
* Copyright (C) 2003-2004 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>_
5
* This program is free software; you can redistribute it and/or modify
6
* it under the terms of the GNU General Public License as published by
7
* the Free Software Foundation; either version 2 of the License
9
* This program is distributed in the hope that it will be useful,
10
* but WITHOUT ANY WARRANTY; without even the implied warranty of
11
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
12
* GNU General Public License for more details.
14
* You should have received a copy of the GNU General Public License
15
* along with this program; if not, write to the Free Software
16
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
20
#include <linux/module.h>
21
#include <linux/types.h>
22
#include <linux/delay.h>
24
#include <asm/uaccess.h>
27
#include "prismcompat.h"
29
#include "islpci_dev.h"
30
#include "islpci_mgt.h"
32
/******************************************************************************
33
Device Interface & Control functions
34
******************************************************************************/
37
* isl38xx_disable_interrupts - disable all interrupts
38
* @device: pci memory base address
40
* Instructs the device to disable all interrupt reporting by asserting
41
* the IRQ line. New events may still show up in the interrupt identification
42
* register located at offset %ISL38XX_INT_IDENT_REG.
45
isl38xx_disable_interrupts(void __iomem *device)
47
isl38xx_w32_flush(device, 0x00000000, ISL38XX_INT_EN_REG);
48
udelay(ISL38XX_WRITEIO_DELAY);
52
isl38xx_handle_sleep_request(isl38xx_control_block *control_block,
53
int *powerstate, void __iomem *device_base)
55
/* device requests to go into sleep mode
56
* check whether the transmit queues for data and management are empty */
57
if (isl38xx_in_queue(control_block, ISL38XX_CB_TX_DATA_LQ))
58
/* data tx queue not empty */
61
if (isl38xx_in_queue(control_block, ISL38XX_CB_TX_MGMTQ))
62
/* management tx queue not empty */
65
/* check also whether received frames are pending */
66
if (isl38xx_in_queue(control_block, ISL38XX_CB_RX_DATA_LQ))
67
/* data rx queue not empty */
70
if (isl38xx_in_queue(control_block, ISL38XX_CB_RX_MGMTQ))
71
/* management rx queue not empty */
74
#if VERBOSE > SHOW_ERROR_MESSAGES
75
DEBUG(SHOW_TRACING, "Device going to sleep mode\n");
78
/* all queues are empty, allow the device to go into sleep mode */
79
*powerstate = ISL38XX_PSM_POWERSAVE_STATE;
81
/* assert the Sleep interrupt in the Device Interrupt Register */
82
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_SLEEP,
84
udelay(ISL38XX_WRITEIO_DELAY);
88
isl38xx_handle_wakeup(isl38xx_control_block *control_block,
89
int *powerstate, void __iomem *device_base)
91
/* device is in active state, update the powerstate flag */
92
*powerstate = ISL38XX_PSM_ACTIVE_STATE;
94
/* now check whether there are frames pending for the card */
95
if (!isl38xx_in_queue(control_block, ISL38XX_CB_TX_DATA_LQ)
96
&& !isl38xx_in_queue(control_block, ISL38XX_CB_TX_MGMTQ))
99
#if VERBOSE > SHOW_ERROR_MESSAGES
100
DEBUG(SHOW_ANYTHING, "Wake up handler trigger the device\n");
103
/* either data or management transmit queue has a frame pending
104
* trigger the device by setting the Update bit in the Device Int reg */
105
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_UPDATE,
106
ISL38XX_DEV_INT_REG);
107
udelay(ISL38XX_WRITEIO_DELAY);
111
isl38xx_trigger_device(int asleep, void __iomem *device_base)
115
#if VERBOSE > SHOW_ERROR_MESSAGES
117
struct timeval current_time;
118
DEBUG(SHOW_FUNCTION_CALLS, "isl38xx trigger device\n");
121
/* check whether the device is in power save mode */
123
/* device is in powersave, trigger the device for wakeup */
124
#if VERBOSE > SHOW_ERROR_MESSAGES
125
do_gettimeofday(¤t_time);
126
DEBUG(SHOW_TRACING, "%08li.%08li Device wakeup triggered\n",
127
current_time.tv_sec, (long)current_time.tv_usec);
129
DEBUG(SHOW_TRACING, "%08li.%08li Device register read %08x\n",
130
current_time.tv_sec, (long)current_time.tv_usec,
131
readl(device_base + ISL38XX_CTRL_STAT_REG));
134
reg = readl(device_base + ISL38XX_INT_IDENT_REG);
135
if (reg == 0xabadface) {
136
#if VERBOSE > SHOW_ERROR_MESSAGES
137
do_gettimeofday(¤t_time);
139
"%08li.%08li Device register abadface\n",
140
current_time.tv_sec, (long)current_time.tv_usec);
142
/* read the Device Status Register until Sleepmode bit is set */
143
while (reg = readl(device_base + ISL38XX_CTRL_STAT_REG),
144
(reg & ISL38XX_CTRL_STAT_SLEEPMODE) == 0) {
145
udelay(ISL38XX_WRITEIO_DELAY);
146
#if VERBOSE > SHOW_ERROR_MESSAGES
151
#if VERBOSE > SHOW_ERROR_MESSAGES
153
"%08li.%08li Device register read %08x\n",
154
current_time.tv_sec, (long)current_time.tv_usec,
155
readl(device_base + ISL38XX_CTRL_STAT_REG));
156
do_gettimeofday(¤t_time);
158
"%08li.%08li Device asleep counter %i\n",
159
current_time.tv_sec, (long)current_time.tv_usec,
163
/* assert the Wakeup interrupt in the Device Interrupt Register */
164
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_WAKEUP,
165
ISL38XX_DEV_INT_REG);
167
#if VERBOSE > SHOW_ERROR_MESSAGES
168
udelay(ISL38XX_WRITEIO_DELAY);
170
/* perform another read on the Device Status Register */
171
reg = readl(device_base + ISL38XX_CTRL_STAT_REG);
172
do_gettimeofday(¤t_time);
173
DEBUG(SHOW_TRACING, "%08li.%08li Device register read %08x\n",
174
current_time.tv_sec, (long)current_time.tv_usec, reg);
177
/* device is (still) awake */
178
#if VERBOSE > SHOW_ERROR_MESSAGES
179
DEBUG(SHOW_TRACING, "Device is in active state\n");
181
/* trigger the device by setting the Update bit in the Device Int reg */
183
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_UPDATE,
184
ISL38XX_DEV_INT_REG);
189
isl38xx_interface_reset(void __iomem *device_base, dma_addr_t host_address)
191
#if VERBOSE > SHOW_ERROR_MESSAGES
192
DEBUG(SHOW_FUNCTION_CALLS, "isl38xx_interface_reset\n");
195
/* load the address of the control block in the device */
196
isl38xx_w32_flush(device_base, host_address, ISL38XX_CTRL_BLK_BASE_REG);
197
udelay(ISL38XX_WRITEIO_DELAY);
199
/* set the reset bit in the Device Interrupt Register */
200
isl38xx_w32_flush(device_base, ISL38XX_DEV_INT_RESET, ISL38XX_DEV_INT_REG);
201
udelay(ISL38XX_WRITEIO_DELAY);
203
/* enable the interrupt for detecting initialization */
205
/* Note: Do not enable other interrupts here. We want the
206
* device to have come up first 100% before allowing any other
208
isl38xx_w32_flush(device_base, ISL38XX_INT_IDENT_INIT, ISL38XX_INT_EN_REG);
209
udelay(ISL38XX_WRITEIO_DELAY); /* allow complete full reset */
213
isl38xx_enable_common_interrupts(void __iomem *device_base)
217
reg = ISL38XX_INT_IDENT_UPDATE | ISL38XX_INT_IDENT_SLEEP |
218
ISL38XX_INT_IDENT_WAKEUP;
219
isl38xx_w32_flush(device_base, reg, ISL38XX_INT_EN_REG);
220
udelay(ISL38XX_WRITEIO_DELAY);
224
isl38xx_in_queue(isl38xx_control_block *cb, int queue)
226
const s32 delta = (le32_to_cpu(cb->driver_curr_frag[queue]) -
227
le32_to_cpu(cb->device_curr_frag[queue]));
229
/* determine the amount of fragments in the queue depending on the type
230
* of the queue, either transmit or receive */
232
BUG_ON(delta < 0); /* driver ptr must be ahead of device ptr */
236
case ISL38XX_CB_TX_MGMTQ:
237
BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE);
239
case ISL38XX_CB_TX_DATA_LQ:
240
case ISL38XX_CB_TX_DATA_HQ:
241
BUG_ON(delta > ISL38XX_CB_TX_QSIZE);
245
case ISL38XX_CB_RX_MGMTQ:
246
BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE);
247
return ISL38XX_CB_MGMT_QSIZE - delta;
249
case ISL38XX_CB_RX_DATA_LQ:
250
case ISL38XX_CB_RX_DATA_HQ:
251
BUG_ON(delta > ISL38XX_CB_RX_QSIZE);
252
return ISL38XX_CB_RX_QSIZE - delta;