2
* Comtrol SV11 card driver
4
* This is a slightly odd Z85230 synchronous driver. All you need to
9
* It supports DMA using two DMA channels in SYNC mode. The driver doesn't
10
* use these facilities
12
* The control port is at io+1, the data at io+3 and turning off the DMA
13
* is done by writing 0 to io+4
15
* The hardware does the bus handling to avoid the need for delays between
16
* touching control registers.
18
* Port B isn't wired (why - beats me)
20
* Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
23
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
25
#include <linux/module.h>
26
#include <linux/kernel.h>
28
#include <linux/net.h>
29
#include <linux/skbuff.h>
30
#include <linux/netdevice.h>
31
#include <linux/if_arp.h>
32
#include <linux/delay.h>
33
#include <linux/hdlc.h>
34
#include <linux/ioport.h>
35
#include <linux/slab.h>
41
#include <asm/byteorder.h>
47
* Network driver support routines
50
static inline struct z8530_dev* dev_to_sv(struct net_device *dev)
52
return (struct z8530_dev *)dev_to_hdlc(dev)->priv;
56
* Frame receive. Simple for our card as we do HDLC and there
57
* is no funny garbage involved
60
static void hostess_input(struct z8530_channel *c, struct sk_buff *skb)
62
/* Drop the CRC - it's not a good idea to try and negotiate it ;) */
63
skb_trim(skb, skb->len - 2);
64
skb->protocol = hdlc_type_trans(skb, c->netdevice);
65
skb_reset_mac_header(skb);
66
skb->dev = c->netdevice;
68
* Send it to the PPP layer. We don't have time to process
75
* We've been placed in the UP state
78
static int hostess_open(struct net_device *d)
80
struct z8530_dev *sv11 = dev_to_sv(d);
88
err = z8530_sync_open(d, &sv11->chanA);
91
err = z8530_sync_dma_open(d, &sv11->chanA);
94
err = z8530_sync_txdma_open(d, &sv11->chanA);
105
z8530_sync_close(d, &sv11->chanA);
108
z8530_sync_dma_close(d, &sv11->chanA);
111
z8530_sync_txdma_close(d, &sv11->chanA);
116
sv11->chanA.rx_function = hostess_input;
122
netif_start_queue(d);
126
static int hostess_close(struct net_device *d)
128
struct z8530_dev *sv11 = dev_to_sv(d);
132
sv11->chanA.rx_function = z8530_null_rx;
139
z8530_sync_close(d, &sv11->chanA);
142
z8530_sync_dma_close(d, &sv11->chanA);
145
z8530_sync_txdma_close(d, &sv11->chanA);
151
static int hostess_ioctl(struct net_device *d, struct ifreq *ifr, int cmd)
153
/* struct z8530_dev *sv11=dev_to_sv(d);
154
z8530_ioctl(d,&sv11->chanA,ifr,cmd) */
155
return hdlc_ioctl(d, ifr, cmd);
159
* Passed network frames, fire them downwind.
162
static netdev_tx_t hostess_queue_xmit(struct sk_buff *skb,
163
struct net_device *d)
165
return z8530_queue_xmit(&dev_to_sv(d)->chanA, skb);
168
static int hostess_attach(struct net_device *dev, unsigned short encoding,
169
unsigned short parity)
171
if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
177
* Description block for a Comtrol Hostess SV11 card
180
static const struct net_device_ops hostess_ops = {
181
.ndo_open = hostess_open,
182
.ndo_stop = hostess_close,
183
.ndo_change_mtu = hdlc_change_mtu,
184
.ndo_start_xmit = hdlc_start_xmit,
185
.ndo_do_ioctl = hostess_ioctl,
188
static struct z8530_dev *sv11_init(int iobase, int irq)
190
struct z8530_dev *sv;
191
struct net_device *netdev;
193
* Get the needed I/O space
196
if (!request_region(iobase, 8, "Comtrol SV11")) {
197
pr_warn("I/O 0x%X already in use\n", iobase);
201
sv = kzalloc(sizeof(struct z8530_dev), GFP_KERNEL);
206
* Stuff in the I/O addressing
211
sv->chanA.ctrlio = iobase + 1;
212
sv->chanA.dataio = iobase + 3;
213
sv->chanB.ctrlio = -1;
214
sv->chanB.dataio = -1;
215
sv->chanA.irqs = &z8530_nop;
216
sv->chanB.irqs = &z8530_nop;
218
outb(0, iobase + 4); /* DMA off */
220
/* We want a fast IRQ for this device. Actually we'd like an even faster
221
IRQ ;) - This is one driver RtLinux is made for */
223
if (request_irq(irq, z8530_interrupt, IRQF_DISABLED,
224
"Hostess SV11", sv) < 0) {
225
pr_warn("IRQ %d already in use\n", irq);
230
sv->chanA.private = sv;
236
* You can have DMA off or 1 and 3 thats the lot
241
outb(0x03 | 0x08, iobase + 4); /* DMA on */
242
if (request_dma(sv->chanA.txdma, "Hostess SV/11 (TX)"))
246
if (request_dma(sv->chanA.rxdma, "Hostess SV/11 (RX)"))
250
/* Kill our private IRQ line the hostess can end up chattering
251
until the configuration is set */
255
* Begin normal initialise
258
if (z8530_init(sv)) {
259
pr_err("Z8530 series device not found\n");
263
z8530_channel_load(&sv->chanB, z8530_dead_port);
264
if (sv->type == Z85C30)
265
z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream);
267
z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream_85230);
272
* Now we can take the IRQ
275
sv->chanA.netdevice = netdev = alloc_hdlcdev(sv);
279
dev_to_hdlc(netdev)->attach = hostess_attach;
280
dev_to_hdlc(netdev)->xmit = hostess_queue_xmit;
281
netdev->netdev_ops = &hostess_ops;
282
netdev->base_addr = iobase;
285
if (register_hdlc_device(netdev)) {
286
pr_err("unable to register HDLC device\n");
291
z8530_describe(sv, "I/O", iobase);
297
free_dma(sv->chanA.rxdma);
300
free_dma(sv->chanA.txdma);
306
release_region(iobase, 8);
310
static void sv11_shutdown(struct z8530_dev *dev)
312
unregister_hdlc_device(dev->chanA.netdevice);
314
free_irq(dev->irq, dev);
317
free_dma(dev->chanA.rxdma);
318
free_dma(dev->chanA.txdma);
320
release_region(dev->chanA.ctrlio - 1, 8);
321
free_netdev(dev->chanA.netdevice);
325
static int io = 0x200;
328
module_param(io, int, 0);
329
MODULE_PARM_DESC(io, "The I/O base of the Comtrol Hostess SV11 card");
330
module_param(dma, int, 0);
331
MODULE_PARM_DESC(dma, "Set this to 1 to use DMA1/DMA3 for TX/RX");
332
module_param(irq, int, 0);
333
MODULE_PARM_DESC(irq, "The interrupt line setting for the Comtrol Hostess SV11 card");
335
MODULE_AUTHOR("Alan Cox");
336
MODULE_LICENSE("GPL");
337
MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
339
static struct z8530_dev *sv11_unit;
341
int init_module(void)
343
if ((sv11_unit = sv11_init(io, irq)) == NULL)
348
void cleanup_module(void)
351
sv11_shutdown(sv11_unit);