2
* drivers/i2c/chips/lm8323.c
4
* Copyright (C) 2007-2009 Nokia Corporation
6
* Written by Daniel Stone <daniel.stone@nokia.com>
7
* Timo O. Karjalainen <timo.o.karjalainen@nokia.com>
9
* Updated by Felipe Balbi <felipe.balbi@nokia.com>
11
* This program is free software; you can redistribute it and/or modify
12
* it under the terms of the GNU General Public License as published by
13
* the Free Software Foundation (version 2 of the License only).
15
* This program is distributed in the hope that it will be useful,
16
* but WITHOUT ANY WARRANTY; without even the implied warranty of
17
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18
* GNU General Public License for more details.
20
* You should have received a copy of the GNU General Public License
21
* along with this program; if not, write to the Free Software
22
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
25
#include <linux/module.h>
26
#include <linux/i2c.h>
27
#include <linux/interrupt.h>
28
#include <linux/sched.h>
29
#include <linux/mutex.h>
30
#include <linux/delay.h>
31
#include <linux/input.h>
32
#include <linux/leds.h>
34
#include <linux/i2c/lm8323.h>
35
#include <linux/slab.h>
37
/* Commands to send to the chip. */
38
#define LM8323_CMD_READ_ID 0x80 /* Read chip ID. */
39
#define LM8323_CMD_WRITE_CFG 0x81 /* Set configuration item. */
40
#define LM8323_CMD_READ_INT 0x82 /* Get interrupt status. */
41
#define LM8323_CMD_RESET 0x83 /* Reset, same as external one */
42
#define LM8323_CMD_WRITE_PORT_SEL 0x85 /* Set GPIO in/out. */
43
#define LM8323_CMD_WRITE_PORT_STATE 0x86 /* Set GPIO pullup. */
44
#define LM8323_CMD_READ_PORT_SEL 0x87 /* Get GPIO in/out. */
45
#define LM8323_CMD_READ_PORT_STATE 0x88 /* Get GPIO pullup. */
46
#define LM8323_CMD_READ_FIFO 0x89 /* Read byte from FIFO. */
47
#define LM8323_CMD_RPT_READ_FIFO 0x8a /* Read FIFO (no increment). */
48
#define LM8323_CMD_SET_ACTIVE 0x8b /* Set active time. */
49
#define LM8323_CMD_READ_ERR 0x8c /* Get error status. */
50
#define LM8323_CMD_READ_ROTATOR 0x8e /* Read rotator status. */
51
#define LM8323_CMD_SET_DEBOUNCE 0x8f /* Set debouncing time. */
52
#define LM8323_CMD_SET_KEY_SIZE 0x90 /* Set keypad size. */
53
#define LM8323_CMD_READ_KEY_SIZE 0x91 /* Get keypad size. */
54
#define LM8323_CMD_READ_CFG 0x92 /* Get configuration item. */
55
#define LM8323_CMD_WRITE_CLOCK 0x93 /* Set clock config. */
56
#define LM8323_CMD_READ_CLOCK 0x94 /* Get clock config. */
57
#define LM8323_CMD_PWM_WRITE 0x95 /* Write PWM script. */
58
#define LM8323_CMD_START_PWM 0x96 /* Start PWM engine. */
59
#define LM8323_CMD_STOP_PWM 0x97 /* Stop PWM engine. */
61
/* Interrupt status. */
62
#define INT_KEYPAD 0x01 /* Key event. */
63
#define INT_ROTATOR 0x02 /* Rotator event. */
64
#define INT_ERROR 0x08 /* Error: use CMD_READ_ERR. */
65
#define INT_NOINIT 0x10 /* Lost configuration. */
66
#define INT_PWM1 0x20 /* PWM1 stopped. */
67
#define INT_PWM2 0x40 /* PWM2 stopped. */
68
#define INT_PWM3 0x80 /* PWM3 stopped. */
70
/* Errors (signalled by INT_ERROR, read with CMD_READ_ERR). */
71
#define ERR_BADPAR 0x01 /* Bad parameter. */
72
#define ERR_CMDUNK 0x02 /* Unknown command. */
73
#define ERR_KEYOVR 0x04 /* Too many keys pressed. */
74
#define ERR_FIFOOVER 0x40 /* FIFO overflow. */
76
/* Configuration keys (CMD_{WRITE,READ}_CFG). */
77
#define CFG_MUX1SEL 0x01 /* Select MUX1_OUT input. */
78
#define CFG_MUX1EN 0x02 /* Enable MUX1_OUT. */
79
#define CFG_MUX2SEL 0x04 /* Select MUX2_OUT input. */
80
#define CFG_MUX2EN 0x08 /* Enable MUX2_OUT. */
81
#define CFG_PSIZE 0x20 /* Package size (must be 0). */
82
#define CFG_ROTEN 0x40 /* Enable rotator. */
84
/* Clock settings (CMD_{WRITE,READ}_CLOCK). */
85
#define CLK_RCPWM_INTERNAL 0x00
86
#define CLK_RCPWM_EXTERNAL 0x03
87
#define CLK_SLOWCLKEN 0x08 /* Enable 32.768kHz clock. */
88
#define CLK_SLOWCLKOUT 0x40 /* Enable slow pulse output. */
90
/* The possible addresses corresponding to CONFIG1 and CONFIG2 pin wirings. */
91
#define LM8323_I2C_ADDR00 (0x84 >> 1) /* 1000 010x */
92
#define LM8323_I2C_ADDR01 (0x86 >> 1) /* 1000 011x */
93
#define LM8323_I2C_ADDR10 (0x88 >> 1) /* 1000 100x */
94
#define LM8323_I2C_ADDR11 (0x8A >> 1) /* 1000 101x */
96
/* Key event fifo length */
97
#define LM8323_FIFO_LEN 15
99
/* Commands for PWM engine; feed in with PWM_WRITE. */
100
/* Load ramp counter from duty cycle field (range 0 - 0xff). */
101
#define PWM_SET(v) (0x4000 | ((v) & 0xff))
102
/* Go to start of script. */
103
#define PWM_GOTOSTART 0x0000
105
* Stop engine (generates interrupt). If reset is 1, clear the program
106
* counter, else leave it.
108
#define PWM_END(reset) (0xc000 | (!!(reset) << 11))
110
* Ramp. If s is 1, divide clock by 512, else divide clock by 16.
111
* Take t clock scales (up to 63) per step, for n steps (up to 126).
112
* If u is set, ramp up, else ramp down.
114
#define PWM_RAMP(s, t, n, u) ((!!(s) << 14) | ((t) & 0x3f) << 8 | \
115
((n) & 0x7f) | ((u) ? 0 : 0x80))
117
* Loop (i.e. jump back to pos) for a given number of iterations (up to 63).
118
* If cnt is zero, execute until PWM_END is encountered.
120
#define PWM_LOOP(cnt, pos) (0xa000 | (((cnt) & 0x3f) << 7) | \
123
* Wait for trigger. Argument is a mask of channels, shifted by the channel
124
* number, e.g. 0xa for channels 3 and 1. Note that channels are numbered
127
#define PWM_WAIT_TRIG(chans) (0xe000 | (((chans) & 0x7) << 6))
128
/* Send trigger. Argument is same as PWM_WAIT_TRIG. */
129
#define PWM_SEND_TRIG(chans) (0xe000 | ((chans) & 0x7))
135
int desired_brightness;
140
struct work_struct work;
141
struct led_classdev cdev;
142
struct lm8323_chip *chip;
148
struct i2c_client *client;
149
struct input_dev *idev;
154
unsigned short keymap[LM8323_KEYMAP_SIZE];
159
struct lm8323_pwm pwm[LM8323_NUM_PWMS];
162
#define client_to_lm8323(c) container_of(c, struct lm8323_chip, client)
163
#define dev_to_lm8323(d) container_of(d, struct lm8323_chip, client->dev)
164
#define cdev_to_pwm(c) container_of(c, struct lm8323_pwm, cdev)
165
#define work_to_pwm(w) container_of(w, struct lm8323_pwm, work)
167
#define LM8323_MAX_DATA 8
170
* To write, we just access the chip's address in write mode, and dump the
171
* command and data out on the bus. The command byte and data are taken as
172
* sequential u8s out of varargs, to a maximum of LM8323_MAX_DATA.
174
static int lm8323_write(struct lm8323_chip *lm, int len, ...)
178
u8 data[LM8323_MAX_DATA];
182
if (unlikely(len > LM8323_MAX_DATA)) {
183
dev_err(&lm->client->dev, "tried to send %d bytes\n", len);
188
for (i = 0; i < len; i++)
189
data[i] = va_arg(ap, int);
194
* If the host is asleep while we send the data, we can get a NACK
195
* back while it wakes up, so try again, once.
197
ret = i2c_master_send(lm->client, data, len);
198
if (unlikely(ret == -EREMOTEIO))
199
ret = i2c_master_send(lm->client, data, len);
200
if (unlikely(ret != len))
201
dev_err(&lm->client->dev, "sent %d bytes of %d total\n",
208
* To read, we first send the command byte to the chip and end the transaction,
209
* then access the chip in read mode, at which point it will send the data.
211
static int lm8323_read(struct lm8323_chip *lm, u8 cmd, u8 *buf, int len)
216
* If the host is asleep while we send the byte, we can get a NACK
217
* back while it wakes up, so try again, once.
219
ret = i2c_master_send(lm->client, &cmd, 1);
220
if (unlikely(ret == -EREMOTEIO))
221
ret = i2c_master_send(lm->client, &cmd, 1);
222
if (unlikely(ret != 1)) {
223
dev_err(&lm->client->dev, "sending read cmd 0x%02x failed\n",
228
ret = i2c_master_recv(lm->client, buf, len);
229
if (unlikely(ret != len))
230
dev_err(&lm->client->dev, "wanted %d bytes, got %d\n",
237
* Set the chip active time (idle time before it enters halt).
239
static void lm8323_set_active_time(struct lm8323_chip *lm, int time)
241
lm8323_write(lm, 2, LM8323_CMD_SET_ACTIVE, time >> 2);
245
* The signals are AT-style: the low 7 bits are the keycode, and the top
246
* bit indicates the state (1 for down, 0 for up).
248
static inline u8 lm8323_whichkey(u8 event)
253
static inline int lm8323_ispress(u8 event)
255
return (event & 0x80) ? 1 : 0;
258
static void process_keys(struct lm8323_chip *lm)
261
u8 key_fifo[LM8323_FIFO_LEN + 1];
262
int old_keys_down = lm->keys_down;
267
* Read all key events from the FIFO at once. Next READ_FIFO clears the
268
* FIFO even if we didn't read all events previously.
270
ret = lm8323_read(lm, LM8323_CMD_READ_FIFO, key_fifo, LM8323_FIFO_LEN);
273
dev_err(&lm->client->dev, "Failed reading fifo \n");
278
while ((event = key_fifo[i++])) {
279
u8 key = lm8323_whichkey(event);
280
int isdown = lm8323_ispress(event);
281
unsigned short keycode = lm->keymap[key];
283
dev_vdbg(&lm->client->dev, "key 0x%02x %s\n",
284
key, isdown ? "down" : "up");
286
if (lm->kp_enabled) {
287
input_event(lm->idev, EV_MSC, MSC_SCAN, key);
288
input_report_key(lm->idev, keycode, isdown);
289
input_sync(lm->idev);
299
* Errata: We need to ensure that the chip never enters halt mode
300
* during a keypress, so set active time to 0. When it's released,
301
* we can enter halt again, so set the active time back to normal.
303
if (!old_keys_down && lm->keys_down)
304
lm8323_set_active_time(lm, 0);
305
if (old_keys_down && !lm->keys_down)
306
lm8323_set_active_time(lm, lm->active_time);
309
static void lm8323_process_error(struct lm8323_chip *lm)
313
if (lm8323_read(lm, LM8323_CMD_READ_ERR, &error, 1) == 1) {
314
if (error & ERR_FIFOOVER)
315
dev_vdbg(&lm->client->dev, "fifo overflow!\n");
316
if (error & ERR_KEYOVR)
317
dev_vdbg(&lm->client->dev,
318
"more than two keys pressed\n");
319
if (error & ERR_CMDUNK)
320
dev_vdbg(&lm->client->dev,
321
"unknown command submitted\n");
322
if (error & ERR_BADPAR)
323
dev_vdbg(&lm->client->dev, "bad command parameter\n");
327
static void lm8323_reset(struct lm8323_chip *lm)
329
/* The docs say we must pass 0xAA as the data byte. */
330
lm8323_write(lm, 2, LM8323_CMD_RESET, 0xAA);
333
static int lm8323_configure(struct lm8323_chip *lm)
335
int keysize = (lm->size_x << 4) | lm->size_y;
336
int clock = (CLK_SLOWCLKEN | CLK_RCPWM_EXTERNAL);
337
int debounce = lm->debounce_time >> 2;
338
int active = lm->active_time >> 2;
341
* Active time must be greater than the debounce time: if it's
342
* a close-run thing, give ourselves a 12ms buffer.
344
if (debounce >= active)
345
active = debounce + 3;
347
lm8323_write(lm, 2, LM8323_CMD_WRITE_CFG, 0);
348
lm8323_write(lm, 2, LM8323_CMD_WRITE_CLOCK, clock);
349
lm8323_write(lm, 2, LM8323_CMD_SET_KEY_SIZE, keysize);
350
lm8323_set_active_time(lm, lm->active_time);
351
lm8323_write(lm, 2, LM8323_CMD_SET_DEBOUNCE, debounce);
352
lm8323_write(lm, 3, LM8323_CMD_WRITE_PORT_STATE, 0xff, 0xff);
353
lm8323_write(lm, 3, LM8323_CMD_WRITE_PORT_SEL, 0, 0);
356
* Not much we can do about errors at this point, so just hope
363
static void pwm_done(struct lm8323_pwm *pwm)
365
mutex_lock(&pwm->lock);
366
pwm->running = false;
367
if (pwm->desired_brightness != pwm->brightness)
368
schedule_work(&pwm->work);
369
mutex_unlock(&pwm->lock);
373
* Bottom half: handle the interrupt by posting key events, or dealing with
374
* errors appropriately.
376
static irqreturn_t lm8323_irq(int irq, void *_lm)
378
struct lm8323_chip *lm = _lm;
382
mutex_lock(&lm->lock);
384
while ((lm8323_read(lm, LM8323_CMD_READ_INT, &ints, 1) == 1) && ints) {
385
if (likely(ints & INT_KEYPAD))
387
if (ints & INT_ROTATOR) {
388
/* We don't currently support the rotator. */
389
dev_vdbg(&lm->client->dev, "rotator fired\n");
391
if (ints & INT_ERROR) {
392
dev_vdbg(&lm->client->dev, "error!\n");
393
lm8323_process_error(lm);
395
if (ints & INT_NOINIT) {
396
dev_err(&lm->client->dev, "chip lost config; "
398
lm8323_configure(lm);
400
for (i = 0; i < LM8323_NUM_PWMS; i++) {
401
if (ints & (1 << (INT_PWM1 + i))) {
402
dev_vdbg(&lm->client->dev,
403
"pwm%d engine completed\n", i);
404
pwm_done(&lm->pwm[i]);
409
mutex_unlock(&lm->lock);
417
static int lm8323_read_id(struct lm8323_chip *lm, u8 *buf)
421
bytes = lm8323_read(lm, LM8323_CMD_READ_ID, buf, 2);
422
if (unlikely(bytes != 2))
428
static void lm8323_write_pwm_one(struct lm8323_pwm *pwm, int pos, u16 cmd)
430
lm8323_write(pwm->chip, 4, LM8323_CMD_PWM_WRITE, (pos << 2) | pwm->id,
431
(cmd & 0xff00) >> 8, cmd & 0x00ff);
435
* Write a script into a given PWM engine, concluding with PWM_END.
436
* If 'kill' is nonzero, the engine will be shut down at the end
437
* of the script, producing a zero output. Otherwise the engine
438
* will be kept running at the final PWM level indefinitely.
440
static void lm8323_write_pwm(struct lm8323_pwm *pwm, int kill,
441
int len, const u16 *cmds)
445
for (i = 0; i < len; i++)
446
lm8323_write_pwm_one(pwm, i, cmds[i]);
448
lm8323_write_pwm_one(pwm, i++, PWM_END(kill));
449
lm8323_write(pwm->chip, 2, LM8323_CMD_START_PWM, pwm->id);
453
static void lm8323_pwm_work(struct work_struct *work)
455
struct lm8323_pwm *pwm = work_to_pwm(work);
456
int div512, perstep, steps, hz, up, kill;
460
mutex_lock(&pwm->lock);
463
* Do nothing if we're already at the requested level,
464
* or previous setting is not yet complete. In the latter
465
* case we will be called again when the previous PWM script
468
if (pwm->running || pwm->desired_brightness == pwm->brightness)
471
kill = (pwm->desired_brightness == 0);
472
up = (pwm->desired_brightness > pwm->brightness);
473
steps = abs(pwm->desired_brightness - pwm->brightness);
476
* Convert time (in ms) into a divisor (512 or 16 on a refclk of
477
* 32768Hz), and number of ticks per step.
479
if ((pwm->fade_time / steps) > (32768 / 512)) {
487
perstep = (hz * pwm->fade_time) / (steps * 1000);
491
else if (perstep > 63)
498
pwm_cmds[num_cmds++] = PWM_RAMP(div512, perstep, s, up);
502
lm8323_write_pwm(pwm, kill, num_cmds, pwm_cmds);
503
pwm->brightness = pwm->desired_brightness;
506
mutex_unlock(&pwm->lock);
509
static void lm8323_pwm_set_brightness(struct led_classdev *led_cdev,
510
enum led_brightness brightness)
512
struct lm8323_pwm *pwm = cdev_to_pwm(led_cdev);
513
struct lm8323_chip *lm = pwm->chip;
515
mutex_lock(&pwm->lock);
516
pwm->desired_brightness = brightness;
517
mutex_unlock(&pwm->lock);
519
if (in_interrupt()) {
520
schedule_work(&pwm->work);
523
* Schedule PWM work as usual unless we are going into suspend
525
mutex_lock(&lm->lock);
526
if (likely(!lm->pm_suspend))
527
schedule_work(&pwm->work);
529
lm8323_pwm_work(&pwm->work);
530
mutex_unlock(&lm->lock);
534
static ssize_t lm8323_pwm_show_time(struct device *dev,
535
struct device_attribute *attr, char *buf)
537
struct led_classdev *led_cdev = dev_get_drvdata(dev);
538
struct lm8323_pwm *pwm = cdev_to_pwm(led_cdev);
540
return sprintf(buf, "%d\n", pwm->fade_time);
543
static ssize_t lm8323_pwm_store_time(struct device *dev,
544
struct device_attribute *attr, const char *buf, size_t len)
546
struct led_classdev *led_cdev = dev_get_drvdata(dev);
547
struct lm8323_pwm *pwm = cdev_to_pwm(led_cdev);
551
ret = strict_strtoul(buf, 10, &time);
552
/* Numbers only, please. */
556
pwm->fade_time = time;
560
static DEVICE_ATTR(time, 0644, lm8323_pwm_show_time, lm8323_pwm_store_time);
562
static int init_pwm(struct lm8323_chip *lm, int id, struct device *dev,
565
struct lm8323_pwm *pwm;
569
pwm = &lm->pwm[id - 1];
574
pwm->desired_brightness = 0;
575
pwm->running = false;
576
pwm->enabled = false;
577
INIT_WORK(&pwm->work, lm8323_pwm_work);
578
mutex_init(&pwm->lock);
582
pwm->cdev.name = name;
583
pwm->cdev.brightness_set = lm8323_pwm_set_brightness;
584
if (led_classdev_register(dev, &pwm->cdev) < 0) {
585
dev_err(dev, "couldn't register PWM %d\n", id);
588
if (device_create_file(pwm->cdev.dev,
589
&dev_attr_time) < 0) {
590
dev_err(dev, "couldn't register time attribute\n");
591
led_classdev_unregister(&pwm->cdev);
600
static struct i2c_driver lm8323_i2c_driver;
602
static ssize_t lm8323_show_disable(struct device *dev,
603
struct device_attribute *attr, char *buf)
605
struct lm8323_chip *lm = dev_get_drvdata(dev);
607
return sprintf(buf, "%u\n", !lm->kp_enabled);
610
static ssize_t lm8323_set_disable(struct device *dev,
611
struct device_attribute *attr,
612
const char *buf, size_t count)
614
struct lm8323_chip *lm = dev_get_drvdata(dev);
618
ret = strict_strtoul(buf, 10, &i);
620
mutex_lock(&lm->lock);
622
mutex_unlock(&lm->lock);
626
static DEVICE_ATTR(disable_kp, 0644, lm8323_show_disable, lm8323_set_disable);
628
static int __devinit lm8323_probe(struct i2c_client *client,
629
const struct i2c_device_id *id)
631
struct lm8323_platform_data *pdata = client->dev.platform_data;
632
struct input_dev *idev;
633
struct lm8323_chip *lm;
639
if (!pdata || !pdata->size_x || !pdata->size_y) {
640
dev_err(&client->dev, "missing platform_data\n");
644
if (pdata->size_x > 8) {
645
dev_err(&client->dev, "invalid x size %d specified\n",
650
if (pdata->size_y > 12) {
651
dev_err(&client->dev, "invalid y size %d specified\n",
656
lm = kzalloc(sizeof *lm, GFP_KERNEL);
657
idev = input_allocate_device();
665
mutex_init(&lm->lock);
667
lm->size_x = pdata->size_x;
668
lm->size_y = pdata->size_y;
669
dev_vdbg(&client->dev, "Keypad size: %d x %d\n",
670
lm->size_x, lm->size_y);
672
lm->debounce_time = pdata->debounce_time;
673
lm->active_time = pdata->active_time;
677
/* Nothing's set up to service the IRQ yet, so just spin for max.
678
* 100ms until we can configure. */
679
tmo = jiffies + msecs_to_jiffies(100);
680
while (lm8323_read(lm, LM8323_CMD_READ_INT, data, 1) == 1) {
681
if (data[0] & INT_NOINIT)
684
if (time_after(jiffies, tmo)) {
685
dev_err(&client->dev,
686
"timeout waiting for initialisation\n");
693
lm8323_configure(lm);
695
/* If a true probe check the device */
696
if (lm8323_read_id(lm, data) != 0) {
697
dev_err(&client->dev, "device not found\n");
702
for (pwm = 0; pwm < LM8323_NUM_PWMS; pwm++) {
703
err = init_pwm(lm, pwm + 1, &client->dev,
704
pdata->pwm_names[pwm]);
709
lm->kp_enabled = true;
710
err = device_create_file(&client->dev, &dev_attr_disable_kp);
714
idev->name = pdata->name ? : "LM8323 keypad";
715
snprintf(lm->phys, sizeof(lm->phys),
716
"%s/input-kp", dev_name(&client->dev));
717
idev->phys = lm->phys;
719
idev->evbit[0] = BIT(EV_KEY) | BIT(EV_MSC);
720
__set_bit(MSC_SCAN, idev->mscbit);
721
for (i = 0; i < LM8323_KEYMAP_SIZE; i++) {
722
__set_bit(pdata->keymap[i], idev->keybit);
723
lm->keymap[i] = pdata->keymap[i];
725
__clear_bit(KEY_RESERVED, idev->keybit);
728
__set_bit(EV_REP, idev->evbit);
730
err = input_register_device(idev);
732
dev_dbg(&client->dev, "error registering input device\n");
736
err = request_threaded_irq(client->irq, NULL, lm8323_irq,
737
IRQF_TRIGGER_LOW|IRQF_ONESHOT, "lm8323", lm);
739
dev_err(&client->dev, "could not get IRQ %d\n", client->irq);
743
i2c_set_clientdata(client, lm);
745
device_init_wakeup(&client->dev, 1);
746
enable_irq_wake(client->irq);
751
input_unregister_device(idev);
754
device_remove_file(&client->dev, &dev_attr_disable_kp);
757
if (lm->pwm[pwm].enabled) {
758
device_remove_file(lm->pwm[pwm].cdev.dev,
760
led_classdev_unregister(&lm->pwm[pwm].cdev);
763
input_free_device(idev);
768
static int __devexit lm8323_remove(struct i2c_client *client)
770
struct lm8323_chip *lm = i2c_get_clientdata(client);
773
disable_irq_wake(client->irq);
774
free_irq(client->irq, lm);
776
input_unregister_device(lm->idev);
778
device_remove_file(&lm->client->dev, &dev_attr_disable_kp);
780
for (i = 0; i < 3; i++)
781
if (lm->pwm[i].enabled) {
782
device_remove_file(lm->pwm[i].cdev.dev, &dev_attr_time);
783
led_classdev_unregister(&lm->pwm[i].cdev);
791
#ifdef CONFIG_PM_SLEEP
793
* We don't need to explicitly suspend the chip, as it already switches off
794
* when there's no activity.
796
static int lm8323_suspend(struct device *dev)
798
struct i2c_client *client = to_i2c_client(dev);
799
struct lm8323_chip *lm = i2c_get_clientdata(client);
802
irq_set_irq_wake(client->irq, 0);
803
disable_irq(client->irq);
805
mutex_lock(&lm->lock);
806
lm->pm_suspend = true;
807
mutex_unlock(&lm->lock);
809
for (i = 0; i < 3; i++)
810
if (lm->pwm[i].enabled)
811
led_classdev_suspend(&lm->pwm[i].cdev);
816
static int lm8323_resume(struct device *dev)
818
struct i2c_client *client = to_i2c_client(dev);
819
struct lm8323_chip *lm = i2c_get_clientdata(client);
822
mutex_lock(&lm->lock);
823
lm->pm_suspend = false;
824
mutex_unlock(&lm->lock);
826
for (i = 0; i < 3; i++)
827
if (lm->pwm[i].enabled)
828
led_classdev_resume(&lm->pwm[i].cdev);
830
enable_irq(client->irq);
831
irq_set_irq_wake(client->irq, 1);
837
static SIMPLE_DEV_PM_OPS(lm8323_pm_ops, lm8323_suspend, lm8323_resume);
839
static const struct i2c_device_id lm8323_id[] = {
844
static struct i2c_driver lm8323_i2c_driver = {
847
.pm = &lm8323_pm_ops,
849
.probe = lm8323_probe,
850
.remove = __devexit_p(lm8323_remove),
851
.id_table = lm8323_id,
853
MODULE_DEVICE_TABLE(i2c, lm8323_id);
855
static int __init lm8323_init(void)
857
return i2c_add_driver(&lm8323_i2c_driver);
859
module_init(lm8323_init);
861
static void __exit lm8323_exit(void)
863
i2c_del_driver(&lm8323_i2c_driver);
865
module_exit(lm8323_exit);
867
MODULE_AUTHOR("Timo O. Karjalainen <timo.o.karjalainen@nokia.com>");
868
MODULE_AUTHOR("Daniel Stone");
869
MODULE_AUTHOR("Felipe Balbi <felipe.balbi@nokia.com>");
870
MODULE_DESCRIPTION("LM8323 keypad driver");
871
MODULE_LICENSE("GPL");